Brian Behlendorf [Sun, 26 Aug 2012 20:34:06 +0000 (13:34 -0700)]
Enhance SPLAT kmem:slab_overcommit test
After the emergency slab objects were merged I started observing
timeout failures in the kmem:slab_overcommit test. These were
due to the ineffecient way the slab_overcommit reclaim function
was implemented. And due to the additional cost of potentially
allocating ten of thousands of emergency objects and tracking
them on a single list.
This patch addresses the first concern by enhansing the test
case to trace all of the allocations objects as a linked list.
This allows for a cleaner version of the reclaim function to
simply release SPLAT_KMEM_OBJ_RECLAIM objects.
Since this touches some common code all the tests which share
these data structions were also updated. After making these
changes slab_overcommit is reliably passing. However, there
is certainly additional cleanup which could be done here.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Thu, 23 Aug 2012 22:36:28 +0000 (15:36 -0700)]
Switch KM_SLEEP to KM_PUSHPAGE
Under certain circumstances the following functions may be called
in a context where KM_SLEEP is unsafe and can result in a deadlocked
system. To avoid this problem the unconditional KM_SLEEPs are
converted to KM_PUSHPAGEs. This will prevent them from attempting
to initiate any I/O during direct reclaim.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Sun, 19 Aug 2012 19:10:19 +0000 (12:10 -0700)]
Mutex ASSERT on self deadlock
Generate an assertion if we're going to deadlock the system by
attempting to acquire a mutex the process is already holding.
There are currently no known instances of this under normal
operation, but it _might_ be possible when using a ZVOL as a
swap device. I want to ensure we catch this immediately if it
were to occur.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Sat, 18 Aug 2012 19:42:28 +0000 (12:42 -0700)]
Add PF_NOFS debugging flag
PF_NOFS is a per-process debug flag which is set in current->flags to
detect when a process is performing an unsafe allocation. All tasks
with PF_NOFS set must strictly use KM_PUSHPAGE for allocations because
if they enter direct reclaim and initiate I/O they may deadlock.
When debugging is disabled, any incorrect usage will be detected and
a call stack with a warning will be printed to the console. The flags
will then be automatically corrected to allow for safe execution. If
debugging is enabled this will be treated as a fatal condition.
To avoid any risk of conflicting with the existing PF_ flags. The
PF_NOFS bit shadows the rarely used PF_MUTEX_TESTER bit. Only when
CONFIG_RT_MUTEX_TESTER is not set, and we know this bit is unused,
will the PF_NOFS bit be valid. Happily, most existing distributions
ship a kernel with CONFIG_RT_MUTEX_TESTER disabled.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Sat, 18 Aug 2012 18:06:21 +0000 (11:06 -0700)]
Revert "Disable vmalloc() direct reclaim"
This reverts commit 2092cf68d89a51eb0d6193aeadabb579dfc4b4a0. The
use of the PF_MEMALLOC flag was always a hack to work around memory
reclaim deadlocks. Those issues are believed to be resolved so this
workaround can be safely reverted.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Sat, 18 Aug 2012 18:05:53 +0000 (11:05 -0700)]
Revert "Fix NULL deref in balance_pgdat()"
This reverts commit b8b6e4c453929596b630fa1cca1ee26a532a2ab4. The
use of the PF_MEMALLOC flag was always a hack to work around memory
reclaim deadlocks. Those issues are believed to be resolved so this
workaround can be safely reverted.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Sat, 18 Aug 2012 18:01:22 +0000 (11:01 -0700)]
Revert "Detect kernels that honor gfp flags passed to vmalloc()"
This reverts commit 36811b4430aaea8c8b91bbe7d812a26799865499.
Which is no longer required because there is now SPL code in
place to safely handle the deadlocks the kernel patch was designed
to address. Therefore we can unconditionally use vmalloc() and
drop all the PF_MEMALLOC code.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Sat, 18 Aug 2012 17:56:17 +0000 (10:56 -0700)]
Revert "Add TASKQ_NORECLAIM flag"
This reverts commit 372c2572336468cbf60272aa7e735b7ca0c3807c. The
use of the PF_MEMALLOC flag was always a hack to work around memory
reclaim deadlocks. Those issues are believed to be resolved so this
workaround can be safely reverted.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This patch is designed to resolve a deadlock which can occur with
__vmalloc() based slabs. The issue is that the Linux kernel does
not honor the flags passed to __vmalloc(). This makes it unsafe
to use in a writeback context. Unfortunately, this is a use case
ZFS depends on for correct operation.
Fixing this issue in the upstream kernel was pursued and patches
are available which resolve the issue.
https://bugs.gentoo.org/show_bug.cgi?id=416685
However, these changes were rejected because upstream felt that
using __vmalloc() in the context of writeback should never be done.
Their solution was for us to rewrite parts of ZFS to accomidate
the Linux VM.
While that is probably the right long term solution, and it is
something we want to pursue, it is not a trivial task and will
likely destabilize the existing code. This work has been planned
for the 0.7.0 release but in the meanwhile we want to improve the
SPL slab implementation to accomidate this expected ZFS usage.
This is accomplished by performing the __vmalloc() asynchronously
in the context of a work queue. This doesn't prevent the posibility
of the worker thread from deadlocking. However, the caller can now
safely block on a wait queue for the slab allocation to complete.
Normally this will occur in a reasonable amount of time and the
caller will be woken up when the new slab is available,. The objects
will then get cached in the per-cpu magazines and everything will
proceed as usual.
However, if the __vmalloc() deadlocks for the reasons described
above, or is just very slow, then the callers on the wait queues
will timeout out. When this rare situation occurs they will attempt
to kmalloc() a single minimally sized object using the GFP_NOIO flags.
This allocation will not deadlock because kmalloc() will honor the
passed flags and the caller will be able to make forward progress.
As long as forward progress can be maintained then even if the
worker thread is deadlocked the critical thread will make progress.
This will eventually allow the deadlocked worker thread to complete
and normal operation will resume.
These emergency allocations will likely be slow since they require
contiguous pages. However, their use should be rare so the impact
is expected to be minimal. If that turns out not to be the case in
practice further optimizations are possible.
One additional concern is if these emergency objects are long lived.
Right now they are simply tracked on a list which must be walked when
an object is freed. Is they accumulate on a system and the list
grows freeing objects will become more expensive. This could be
handled relatively easily by using a hash instead of a list, but that
optimization (if needed) is left for a follow up patch.
Additionally, these emeregency objects could be repacked in to existing
slabs as objects are freed if the kmem_cache_set_move() functionality
was implemented. See issue https://github.com/zfsonlinux/spl/issues/26
for full details. This work would also help reduce ZFS's memory
fragmentation problems.
The /proc/spl/kmem/slab file has had two new columns added at the
end. The 'emerg' column reports the current number of these emergency
objects in use for the cache, and the following 'max' column shows
the historical worst case. These value should give us a good idea
of how often these objects are needed. Based on these values under
real use cases we can tune the default behavior.
Lastly, as a side benefit using a single work queue for the slab
allocations should reduce cpu contention on the global virtual address
space lock. This should manifest itself as reduced cpu usage for
the system.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Prakash Surya [Fri, 24 Aug 2012 17:42:12 +0000 (10:42 -0700)]
Add kpreempt_[dis|en]able macros in <sys/disp.h>
To support preempt enabled kernels in ZFS on Linux, there are a couple
places where the ZFS code needs to disable interrupts. This change adds
the Solaris preempt functions and maps them to the equivalent ZFS
functions, allowing the ZFS to make use of them.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #98
Prakash Surya [Thu, 23 Aug 2012 21:00:58 +0000 (14:00 -0700)]
Avoid calling smp_processor_id in spl_magazine_age
The spl_magazine_age function had the implied assumption that it will
remain on its current cpu through its execution. In order to support
preempt enabled kernels, this assumption had to be removed.
The spl_kmem_magazine structure now holds the cpu id of the cpu it is
local to. This allows spl_magazine_age to use this field when scheduling
work to be done by the magazine's local cpu.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #98
Richard Yao [Thu, 16 Aug 2012 18:55:42 +0000 (14:55 -0400)]
Remove Makefile from non-toplevel .gitignore files
When building SPL support into the kernel, ./copy-builtin will copy
non-toplevel .gitignore files. These files list /Makefile, which causes
git-archive to omit ./module/{spl,splat}/Makefile. The absence of these
files result in build failures when SPL is selected. ZFS is unaffected
because it puts Makefile in the toplevel .gitignore, which is not
copied. We fix SPL by emulating that behavior.
Reported-by: Fabio Erculiani <lxnay@gentoo.org> Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #152
Prakash Surya [Wed, 22 Aug 2012 19:30:59 +0000 (12:30 -0700)]
Wrap trace_set_debug_header in trace_[get|put]_tcd
To properly support CONFIG_PREEMPT enabled kernels, we must refrain from
using a CPU index when preemption is enabled. As a result, this change
moves the trace_set_debug_header call (which calls smp_processor_id)
within trace_get_tcd and trace_put_tcd (which disable and enable
preemption respectively).
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #160
Brian Behlendorf [Mon, 13 Aug 2012 23:23:45 +0000 (16:23 -0700)]
Cleanly remove spl-modules-devel headers
Add the /usr/src/spl-<version>-<release>/<kernel> directory to
the spl-modules-devel package. This ensures that this directory
will be removed when the package is removed.
We do not include the higher level /usr/src/spl-<version>-<release>
directory since there may be builds for multiple kernels. Instead,
a %postun rmdir is added which attempts to remove this directory.
It will only succeed when the last spl-modules-devel-* package
for this specific release is removed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Prakash Surya [Tue, 7 Aug 2012 20:57:03 +0000 (13:57 -0700)]
Support building a spl-modules-dkms sub package
This commit adds support for building a spl-modules-dkms sub package
built around Dynamic Kernel Module Support. This is to allow building
packages using the DKMS infrastructure which is intended to ease the
burden of kernel version changes, upgrades, etc.
By default spl-modules-dkms-* sub package will be built as part of
the 'make rpm' target. Alternately, you can build only the DKMS
module package using the 'make rpm-dkms' target.
Examples:
# To build packaged binaries as well as a dkms packages
$ ./configure && make rpm
# To build only the packaged binary utilities and dkms packages
$ ./configure && make rpm-utils rpm-dkms
Note: Only the RHEL 5/6, CHAOS 5, and Fedora distributions are
supported for building the dkms sub package.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue zfsonlinux/zfs#535
In the comments of commit 723aa3b0c2eed070f7eeadd2ce2d87f46da6d0f8,
mmatuska reported that the test for invalidate_inodes_check() is broken
if invalidate_inodes() takes two arguments.
This patch fixes the issue by resorting to another approach for
detecting invalidate_inodes_check(): is simply checks if
invalidate_inodes is defined as a macro. If it is, then it concludes
that invalidate_inodes_check() is available. This will continue to work
even if the prototype of invalidate_inodes_check() changes over time.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #148
Brian Behlendorf [Thu, 26 Jul 2012 22:30:47 +0000 (15:30 -0700)]
Merge branch 'builtin-clean'
Support in-tree builtin module building.
These commits add support for compiling the SPL module as a built-in
kernel module by copying the module code into the kernel source tree.
Here's the procedure:
- Create your kernel configuration (`.config` file) as usual. This
has to be done first so that SPL's configure script is able to
detect kernel features correctly.
- Run `make prepare scripts` inside the kernel source tree.
- Run `./configure --enable-linux-builtin --with-linux=/usr/src/linux-...`
inside the SPL directory.
- Run `./copy-builtin /usr/src/linux-...` inside the SPL directory.
- In the kernel source tree, enable the `CONFIG_SPL` option
(e.g. using `make menuconfig`).
- Build the kernel as usual.
SPL module parameters can be set at boot time using the following syntax
on the kernel command line: `spl.parameter_name=parameter_value`.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue zfsonlinux/zfs#851
Currently, the SPL tries to determine the hostid at module load. The
hostid is usually determined by running the userland program "hostid"
during module initialization.
Unfortunately, when the module initializes, it may be way too soon to be
able to run any userland programs. This is especially true when the
module is compiled directly inside the kernel (built-in); in that case,
the SPL would try to run hostid when the kernel is still initializing,
which of course is doomed to fail.
This patch fixes the issue by deferring hostid generation until
something actually needs the hostid (that is, when zone_get_hostid() is
called), thus switching to a "on-initialization" model to a "on-demand"
(lazy loading) model. ZFS only needs the hostid when some pool
operations are requested, and this always happens way after the kernel
has finished initialization, thus solving the problem.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue zfsonlinux/zfs#851
This commit introduces a "copy-builtin" script designed to prepare a
kernel source tree for building SPL as a builtin module. The script
makes a full copy of all needed files, thus making the kernel source
tree fully independent of the spl source package.
To achieve that, some compilation flags (-include, -I) have been moved
to module/Makefile. This Makefile is only used when compiling external
modules; when compiling builtin modules, a Kbuild file generated by the
configure-builtin script is used instead. This makes sure Makefiles
inside the kernel source tree does not contain references to the spl
source package.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue zfsonlinux/zfs#851
This patch adds a new autoconf function: SPL_LINUX_TRY_COMPILE_SYMBOL.
This new function does the following:
- Call LINUX_TRY_COMPILE with the specified parameters.
- If unsuccessful, return false.
- If successful and we're configuring with --enable-linux-builtin,
return true.
- Else, call CHECK_SYMBOL_EXPORT with the specified parameters and
return the result.
All calls to CHECK_SYMBOL_EXPORT are converted to
LINUX_TRY_COMPILE_SYMBOL so that the tests work even when configuring
for builtin on a kernel which doesn't have loadable module support, or
hasn't been built yet.
The only exception are:
- AC_GET_VMALLOC_INFO, because we don't even have a public header to
include in the test case, but that's okay considering this symbol can
be ignored just fine.
- SPL_AC_DEVICE_CREATE, which is legacy API for 2.6.18 kernels. Since
kernels this old are no longer supported it should arguably just be
removed entirely from the build system.
Note that we're also checking for the correct prototype with an actual
call, which was not the case with CHECK_SYMBOL_EXPORT. However, for
"complicated" test cases like with multiple symbol versions (e.g.
vfs_fsync), we stick with the original behavior and only check for the
function's existence.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue zfsonlinux/zfs#851
Currently, when building a test case, we're compiling an entire Linux
module from beginning to end. This includes the MODPOST stage, which
generates a "conftest.mod.c" file with some boilerplate module
declaration code.
This poses a problem when configuring for built-in on kernels which have
loadable module support disabled. In this case conftest.mod.c is
referencing disabled code, resulting in a compilation failure, thus
breaking the tests.
This patch fixes the issue by faking the modpost stage when the
--enable-linux-builtin option is provided. It does so by forcing the
modpost command to be /bin/true, and using an empty conftest.mod.c file.
The test module still compiles fine, although the result isn't loadable,
but we don't really care at this point.
Note it is important to preserve the modpost stage when building out of
tree. This allows for the posibility of configure checks to leverage
this phase to identify GPL-only symbols.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue zfsonlinux/zfs#851
This patch adds a new option to configure: --enable-linux-builtin. When
this option is used, the following happens:
- Compilation of kernel modules is disabled.
- A failure to find UTS_RELEASE is followed by a suggestion to run
"make prepare" on the kernel source tree.
This patch also adds a new test which tries to compile an empty module
as a basic toolchain sanity test. If it fails and the option was
specified, the error is followed by a suggestion to run "make scripts"
on the kernel source tree.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue zfsonlinux/zfs#851
Commit 3160d4f56bf35492e9c400094f8c1ff2066d4459 changed the set of
conditions under which spl_mutex_spin_max would be implemented as a
function by changing an #if in sys/mutex.h. The corresponding
implementation file spl-mutex.c, however, has not been updated to
reflect the change. This results in undefined reference errors on
spl_mutex_spin_max under the following condition:
Currently, when configure --with-config is used, selective compilation
is only effective for the simple "make" case. Package builders (e.g.
make rpm) still build everything (utils and modules). This patch fixes
that.
This patch also drops the duplicate rpm-modules build target.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Prakash Surya <surya1@llnl.gov>
Issue zfsonlinux/zfs#851
In zfs, each module Makefile contains a MODULE variable which contains
the name of the module, and the following declarations reference this
variable.
In spl, there is a MODULES variable which is never used. Rename it to
MODULE and use it like in zfs. This improves consistency between the two
build systems.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue zfsonlinux/zfs#851
Brian Behlendorf [Fri, 20 Jul 2012 18:12:19 +0000 (11:12 -0700)]
32-bit compat, hostid_read()
Explicitly cast the sizeof in hostid_read() to prevent the
following compiler warning on 32-bit systems.
module/spl/spl-generic.c:490:10: error: format '%lu' expects
argument of type 'long unsigned int', but argument 4 has type
'unsigned int' [-Werror=format]
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Fri, 13 Jul 2012 19:49:40 +0000 (12:49 -0700)]
Optimize spl_rwsem_is_locked()
The spl_rwsem_is_locked() compatibility function has been observed
to be a hot spot. The root cause of this is that we must check the
rwsem activity under the rwsem->wait_lock to avoid a race. When
the lock is busy significant contention can occur.
The upstream kernel fix for this race had the insight that by using
spin_trylock_irqsave() this contention could be avoided. When the
lock is contended it's reasonable to return that it is locked.
This change updates the SPLs implemention to be like the upstream
kernel. Since the kernel code has been in use for years now this
a low risk change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Previously, the spl.release file was created at 'make install' time.
This is slightly problematic when the file is needed without running
'make install'. Because of this, the step creating the file was removed
from 'make install' and replaced with a more appropriate spl.release.in
file.
As a result, the spl.release file will now be created earlier as part
of the 'configure' step as opposed to the 'make install' step.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #135
Richard Yao [Thu, 7 Jun 2012 02:38:12 +0000 (22:38 -0400)]
Detect kernels that honor gfp flags passed to vmalloc()
zfsonlinux/spl@2092cf68d89a51eb0d6193aeadabb579dfc4b4a0 used
PF_MEMALLOC to workaround a bug in the Linux kernel where
allocations did not honor the gfp flags passed to vmalloc().
Unfortunately, PF_MEMALLOC has the side effect of permitting
allocations to allocate pages outside of ZONE_NORMAL. This
has been observed to result in the depletion of ZONE_DMA32.
A kernel patch is available in the Gentoo bug tracker for
this issue.
https://bugs.gentoo.org/show_bug.cgi?id=416685
This negates any benefit PF_MEMALLOC provides, so we introduce
an autotools check to disable the use of PF_MEMALLOC on
systems with patched kernels.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #126
Richard Yao [Mon, 25 Jun 2012 17:22:21 +0000 (13:22 -0400)]
Constify memory management functions
This prevents warnings in ZFS that were caused by changes necessary to
support PaX patched kernels. When debugging is enabled, these warnings
become build failures.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #131
Prakash Surya [Mon, 7 May 2012 18:26:05 +0000 (11:26 -0700)]
Support debug and debug-devel sub packages
This commit adds support for building debug and debug-devel sub packages
of the spl-modules main package. This is to allow building packages
which are built against a debug kernel. By default, only packages are
built against a regular non-debug kernel. This can be toggled by passing
the '--with kernel-debug' parameter to rpmbuild.
Examples:
# To build packages against only the non-debug kernel
$ rpmbuild --rebuild --with kernel --without kernel-debug $SRPM
# To build packages against only the debug kernel
$ rpmbuild --rebuild --without kernel --with kernel-debug $SRPM
# To build packages against debug and non-debug kernel
$ rpmbuild --rebuild --with kernel --with kernel-debug $SRPM
Note: Only the RHEL 5/6, CHAOS 5, and Fedora distributions are supported
for building the debug and debug-devel packages.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #115
Brian Behlendorf [Fri, 29 Jun 2012 18:54:52 +0000 (11:54 -0700)]
PowerPC Compatibility
Usage of get_current() is not supported across all architectures.
The correct interface to use is the '#define current' which will
map to the appropriate function, usually current_thread_info().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #119
Richard Yao [Wed, 6 Jun 2012 16:51:53 +0000 (16:51 +0000)]
Linux 3.4 compat, __clear_close_on_exec replaces FD_CLR
torvalds/linux@1dce27c5aa6770e9d195f2bb7db1db3d4dde5591 introduced
__clear_close_on_exec() as a replacement for FD_CLR. Further commits
appear to have removed FD_CLR from the Linux source tree. This
causes the following failure:
error: implicit declaration of function '__FD_CLR'
[-Werror=implicit-function-declaration]
To correct this we update the code to use the current
__clear_close_on_exec() interface for readability. Then we introduce
an autotools check to determine if __clear_close_on_exec() is available.
If it isn't then we define some compatibility logic which used the older
FD_CLR() interface.
Signed-off-by: Richard Yao <ryao@gentoo.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #124
Brian Behlendorf [Wed, 13 Jun 2012 20:43:29 +0000 (13:43 -0700)]
Fix uninit variable in slab reclaim test
Gcc version 4.7.0 reports the delta.tv_sec in the slab reclaim test
as potentially unitialized. In practice this will never occur but
to keep gcc happy we initialize the variable to zero.
Signed-off-by: Brian Behlendorf <behlendo@fedora-17-amd64.(none)>
Brian Behlendorf [Mon, 11 Jun 2012 16:12:37 +0000 (09:12 -0700)]
Fix invalid context bug
In the module unload path the vm_file_cache was being destroyed
under a spin lock. Because this operation might sleep it was
possible, although very very unlikely, that this could result
in a deadlock.
This issue was indentified by using a Linux debug kernel and
has been fixed by moving the kmem_cache_destroy() out from under
the spin lock. There is no need to lock this operation here.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes zfsonlinux/zfs#771
Jorgen Lundman [Tue, 15 May 2012 05:45:09 +0000 (05:45 +0000)]
Fix ARM 64-bit division
Correctly implementating 64-bit division for ARM requires more than
just providing the __aeabi_uldivmod() and __aeabi_ldivmod() symbols.
They are need to be implemented is such a way that the quotient and
remainder and left in specific registers after the division operation
completes. This change updates the wrapper functions to accomplish
this according to the official ARM Run-time ABI.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes zfsonlinux/zfs#706
Brian Behlendorf [Thu, 10 May 2012 23:25:23 +0000 (16:25 -0700)]
Remove Solaris module emulation
Originally I believed that these interfaces would be needed.
However, in practice it turned out that it was more straight
forward and maintainable to use the native Linux interfaces.
As such, this is all dead code and can be safely removed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #109
Richard Yao [Tue, 1 May 2012 13:34:39 +0000 (09:34 -0400)]
Modify KM_PUSHPAGE to use GFP_NOIO instead of GFP_NOFS
The resolution of issue #31 made KM_PUSHPAGE imply GFP_NOFS. This
was done to prevent situations where filesystem operations which are
holding locks enter direct reclaim and attempt to reaquire those
same locks. This clearly will result in a deadlock.
This works for datasets which are implemented in terms for filesystem
operations. But unfortunately, swapping to a zvol will encounter
many of the same deadlocks and GFP_NOFS will not prevent this. As
such, it is appropriate to extend KM_PUSHPAGE to use the broader
GFP_NOIO mask to handle these non-filesystem cases.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue zfsonlinux/zfs#342
Closes #105
This test is designed to verify that direct reclaim is functioning as
expected. We allocate a large number of objects thus creating a large
number of slabs. We then apply memory pressure and expect that the
direct reclaim path can easily recover those slabs. The registered
reclaim function will free the objects and the slab shrinker will call
it repeatedly until at least a single slab can be freed.
Note it may not be possible to reclaim every last slab via direct reclaim
without a failure because the shrinker_rwsem may be contended. For this
reason, quickly reclaiming 3/4 of the slabs is considered a success.
This should all be possible within 10 seconds. For reference, on a
system with 2G of memory this test takes roughly 0.2 seconds to run.
It may take longer on larger memory systems but should still easily
complete in the alloted 10 seconds.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #107
To minimize the chance of triggering an OOM during direct reclaim.
The kmem caches have been improved to make a best effort to reclaim
at least one slab when a reclaim function is registered. This helps
avoid the case where objects are released but they are spread over
multiple slabs so no memory gets reclaimed.
Care has been taken to avoid deadlocking if the reclaim function
is unable to make forward progress. Additionally, the reclaim
function may be skipped entirely if there are already free slabs
which can be safely reaped.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #107
The Linux direct reclaim path uses this out of band value to
determine if forward progress is being made. Normally this is
incremented by kmem_freepages() which is part of the various
Linux slab implementations. However, since we are using none
of that infrastructure we're responsible for incrementing this
count.
If no forward progress is detected and a subsequent allocation
fails the OOM killer will be invoked. If there was forward
progress additional reclaim will be attempted via the page
cache and registerd shrinker until the allocation succeeds.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #107
When memory pressure triggers direct memory reclaim, a slabs age
and delay should not prevent it from being freed. This patch ensures
these values are ignored, allowing an empty slab to be freed in this
code path no matter the value of its age and delay.
This prevents needless scanning of the partial slabs and has been
observed to significantly reduce the total cpu usage. In addition,
it should allow for snappier reclaim under memory pressure.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #102
Throttle number of freed slabs based on nr_to_scan
Previously, the SPL tried to maintain Solaris semantics by freeing
all available (empty) slabs from its slab caches when the shrinker
was called. This is not desirable when running on Linux. To make
the SPL shrinker more Linux friendly, the actual number of freed
slabs from each of the slab caches is now derived from nr_to_scan
and skc_slab_objs.
Additionally, an accounting bug was fixed in spl_slab_reclaim()
which could cause us to reclaim one more slab than requested.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #101
Jorgen Lundman [Wed, 2 May 2012 00:15:28 +0000 (00:15 +0000)]
Add missing 64-bit divide for 32-bit ARM
Leverage the existing generic 64-bit division operations which
were originally implemented for x86 to support ARM. All that is
required is to make the symbols available to the linker with the
expected names.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
To lay the ground work for introducing the taskq_dispatch_prealloc()
interface, the tq_work_list and tq_threads fields had to be replaced
with new alternatives in the taskq_t structure.
the comment above taskq_wait_check has been incorrect. This change is an
attempt at bringing that description more in line with the current
implementation. Essentially, references to the old task work list had to
be updated to reference the new taskq thread active list.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #65
Long ago I added support to the spl for condition variable names
because I thought they might be needed. It turns out they aren't.
In fact the official Solaris cv_init(9F) man page discourages
their use in the kernel.
cv_init(9F)
Parameters
name - Descriptive string. This is obsolete and should be
NULL. (Non-NULL strings are legal, but they're a
waste of kernel memory.)
Therefore, I'm removing them from the spl to reclaim this memory
and adding an ASSERT() to ensure no new consumers are added which
make use of the name.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Improve the distribution detection by moving the tests for
distribution specific files first. The Ubuntu and Debian
checks are left for last because they are the least likely
to be unique. This is particularly true in the case of Debian
since so many distributions are based on Debian.
Since this is currently only used to identify the correct
packaging method for this system the result in many instances
is simply cosmetic.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Mon, 27 Feb 2012 18:42:07 +0000 (10:42 -0800)]
Cleanly support debug packages
Allow a source rpm to be rebuilt with debugging enabled. This
avoids the need to have to manually modify the spec file. By
default debugging is still largely disabled. To enable specific
debugging features use the following options with rpmbuild.
Brian Behlendorf [Fri, 10 Feb 2012 00:38:42 +0000 (16:38 -0800)]
Add missing spl_debug_* helpers
When building the spl with --disable-debug-log the __SDEBUG()
macro and spl_debug_* helper functions were undefined. This
change adds the missing functions so the upper layers compiling
against the spl don't need to be aware of how the spl was built.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Sat, 21 Jan 2012 00:39:12 +0000 (16:39 -0800)]
Add --enable-debug-log configure option
Until now the notion of an internal debug logging infrastructure
was conflated with enabling ASSERT()s. This patch clarifies things
by cleanly breaking the two subsystem apart. The result of this
is the following behavior.
--enable-debug - Enable/disable code wrapped in ASSERT()s.
--disable-debug ASSERT()s are used to check invariants and
are never required for correct operation.
They are disabled by default because they
may impact performance.
--enable-debug-log - Enable/disable the debug log infrastructure.
--disable-debug-log This infrastructure allows the spl code and
its consumer to log messages to an in-kernel
log. The granularity of the logging can be
controlled by a debug mask. By default the
mask disables most debug messages resulting
in a negligible performance impact. Because
of this the debug log is enabled by default.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ned Bass [Thu, 19 Jan 2012 18:33:19 +0000 (10:33 -0800)]
Taskq locking optimizations
Testing has shown that tq->tq_lock can be highly contended when a
large number of small work items are dispatched. The lock hold time
is reduced by the following changes:
1) Use exclusive threads in the work_waitq
When a single work item is dispatched we only need to wake a single
thread to service it. The current implementation uses non-exclusive
threads so all threads are woken when the dispatcher calls wake_up().
If a large number of threads are in the queue this overhead can become
non-negligible.
2) Conditionally add/remove threads from work waitq
Taskq threads need only add themselves to the work wait queue if
there are no pending work items.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #32
A race condition was introduced by which a wake_up() call can be lost
after the taskq thread determines there is no pending work items,
leading to deadlock:
This could easily happen if an interrupt for an IO completion was
outstanding at the point where the taskq thread reenables interrupts,
just before the call to add_wait_queue_exclusive(). The handler would
run immediately within the race window.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #32
Brian Behlendorf [Wed, 18 Jan 2012 00:14:59 +0000 (16:14 -0800)]
Fix rpm dependencies
This change updates the rpm spec files to have strictly correct
package dependencies. That means a few things:
* Add a dependency to the spl package for the spl-modules package.
This ensures that when running 'yum install spl' that newest
version of the spl-modules will be installed.
* Remove the redundant distribution release extension. This
is already added once because it is part of the kernel package
release name.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Wed, 18 Jan 2012 00:14:35 +0000 (16:14 -0800)]
Add the release component to headers
When the original build system code was added the release
component was accidentally omited from the development header
install path. This patch adds the missing path component so
it's always clear exactly what release your compiling against.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ned Bass [Tue, 17 Jan 2012 23:34:55 +0000 (15:34 -0800)]
Taskq locking optimizations
Testing has shown that tq->tq_lock can be highly contended when a
large number of small work items are dispatched. The lock hold time
is reduced by the following changes:
1) Use exclusive threads in the work_waitq
When a single work item is dispatched we only need to wake a single
thread to service it. The current implementation uses non-exclusive
threads so all threads are woken when the dispatcher calls wake_up().
If a large number of threads are in the queue this overhead can become
non-negligible.
2) Conditionally add/remove threads from work waitq outside of tq_lock
Taskq threads need only add themselves to the work wait queue if there
are no pending work items. Furthermore, the add and remove function
calls can be made outside of the taskq lock since the wait queues are
protected from concurrent access by their own spinlocks.
3) Call wake_up() outside of tq->tq_lock
Again, the wait queues are protected by their own spinlock, so the
dispatcher functions can drop tq->tq_lock before calling wake_up().
A new splat test taskq:contention was added in a prior commit to measure
the impact of these changes. The following table summarizes the
results using data from the kernel lock profiler.
Each row reflects the average result over 5 test runs.
/proc/lock_stats was zeroed out before and collected after each run.
Column 1 is the cumulative hold time in microseconds for tq->tq_lock.
The tests are cumulative; each row reflects the code changes of the
previous rows. %diff is calculated with respect to "original" as
100*(orig-new)/orig.
Although calling wake_up() outside of the taskq lock dramatically
reduced the taskq lock hold time, the test actually took slightly more
wall clock time. This is because the point of contention shifts from
the taskq lock to the wait queue lock. But the change still seems
worthwhile since it removes our taskq implementation as a bottleneck,
assuming the small increase in wall clock time to be statistical
noise.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #32
Ned Bass [Tue, 17 Jan 2012 22:23:58 +0000 (14:23 -0800)]
Add taskq contention splat test
Add a test designed to generate contention on the taskq spinlock by
using a large number of threads (100) to perform a large number (131072)
of trivial work items from a single queue. This simulates conditions
that may occur with the zio free taskq when a 1TB file is removed from a
ZFS filesystem, for example. This test should always pass. Its purpose
is to provide a benchmark to easily measure the effectiveness of taskq
optimizations using statistics from the kernel lock profiler.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #32
Additionally quote @LINUX_SYMBOLS@ because it is a null substitution
in this configuration, which results in a `[ -f ]` expression that
incorrectly evaluates to true.
# ./configure --with-config=user
# make distclean
Making distclean in module
make[1]: Entering directory `/spl/module'
make -C SUBDIRS=`pwd` clean
make: Entering an unknown directory
make: *** SUBDIRS=/spl/module: No such file or directory. Stop.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Fri, 13 Jan 2012 17:08:12 +0000 (09:08 -0800)]
Run SPL_AC_PACMAN only if $VENDOR is "arch"
Unfortunately, Arch's package manager `pacman` shares it's name with a
popular arcade video game. Thus, in order to refrain from executing the
video game when we mean to execute the package manager, SPL_AC_PACMAN is
now only run when $VENDOR is determined to be "arch".
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes zfsonlinux/zfs#517
Wrap spin_lock_* function calls in a new spl_rwsem_* interface to
ensure type safety if raw_spinlock_t becomes architecture specific,
and to satisfy these compiler warnings:
warning: passing argument 1 of ‘spinlock_check’
from incompatible pointer type [enabled by default]
note: expected ‘struct spinlock_t *’
but argument is of type ‘struct raw_spinlock_t *’
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Closes: #76 Closes: zfsonlinux/zfs#463
Brian Behlendorf [Wed, 21 Dec 2011 22:22:45 +0000 (14:22 -0800)]
Proxmox VE kernel compat, invalidate_inodes()
The Proxmox VE kernel contains a patch which renames the function
invalidate_inodes() to invalidate_inodes_check(). In the process
it adds a 'check' argument and a '#define invalidate_inodes(x)'
compatibility wrapper for legacy callers. Therefore, if either
of these functions are exported invalidate_inodes() can be
safely used.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #58
Prakash Surya [Sat, 17 Dec 2011 06:16:47 +0000 (22:16 -0800)]
Move Arch Linux's VENDOR check above Ubuntu's
If the lsb-release package is installed on an Arch Linux distribution,
the configure step will incorrectly detect the running distribution as
Ubuntu. This is a result of both distributions providing an
/etc/lsb-release file, and the Ubuntu VENDOR check being performed
first.
Since the Arch Linux test check's for a file more specific to the Arch
Linux distribution, moving Arch Linux's VENDOR check above Unbuntu's
check provides a quick and easy solution.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #72
Prakash Surya [Fri, 16 Dec 2011 22:57:31 +0000 (14:57 -0800)]
Store copy of tqent_flags prior to servicing task
A preallocated taskq_ent_t's tqent_flags must be checked prior to
servicing the taskq_ent_t. Once a preallocated taskq entry is serviced,
the ownership of the entry is handed back to the caller of
taskq_dispatch, thus the entry's contents can potentially be mangled.
In particular, this is a problem in the case where a preallocated taskq
entry is serviced, and the caller clears it's tqent_flags field. Thus,
when the function returns and task_done is called, it looks as though
the entry is **not** a preallocated task (when in fact it **is** a
preallocated task).
In this situation, task_done will place the preallocated taskq_ent_t
structure onto the taskq_t's free list. This is a **huge** mistake. If
the taskq_ent_t is then freed by the caller of taskq_dispatch, the
taskq_t's free list will hold a pointer to garbage data. Even worse, if
nothing has over written the freed memory before the pointer is
dereferenced, it may still look as though it points to a valid list_head
belonging to a taskq_ent_t structure.
Thus, the task entry's flags are now copied prior to servicing the task.
This copy is then checked to see if it is a preallocated task, and
determine if the entry needs to be passed down to the task_done
function.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #71
Prakash Surya [Fri, 16 Dec 2011 17:44:31 +0000 (09:44 -0800)]
Swap taskq_ent_t with taskqid_t in taskq_thread_t
The taskq_t's active thread list is sorted based on its
tqt_ent->tqent_id field. The list is kept sorted solely by inserting
new taskq_thread_t's in their correct sorted location; no other
means is used. This means that once inserted, if a taskq_thread_t's
tqt_ent->tqent_id field changes, the list runs the risk of no
longer being sorted.
Prior to the introduction of the taskq_dispatch_prealloc() interface,
this was not a problem as a taskq_ent_t actively being serviced under
the old interface should always have a static tqent_id field. Thus,
once the taskq_thread_t is added to the taskq_t's active thread list,
the taskq_thread_t's tqt_ent->tqent_id field would remain constant.
Now, this is no longer the case. Currently, if using the
taskq_dispatch_prealloc() interface, any given taskq_ent_t actively
being serviced _may_ have its tqent_id value incremented. This happens
when the preallocated taskq_ent_t structure is recursively dispatched.
Thus, a taskq_thread_t could potentially have its tqt_ent->tqent_id
field silently modified from under its feet. If this were to happen
to a taskq_thread_t on a taskq_t's active thread list, this would
compromise the integrity of the order of the list (as the list
_may_ no longer be sorted).
To get around this, the taskq_thread_t's taskq_ent_t pointer was
replaced with its own static copy of the tqent_id. So, as a taskq_ent_t
is pulled off of the taskq_t's pending list, a static copy of its
tqent_id is made and this copy is used to sort the active thread
list. Using a static copy is key in ensuring the integrity of the
order of the active thread list. Even if the underlying taskq_ent_t
is recursively dispatched (as has its tqent_id modified), this
static copy stored inside the taskq_thread_t will remain constant.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #71
Prakash Surya [Wed, 7 Dec 2011 01:33:51 +0000 (17:33 -0800)]
Add make rule for building Arch Linux packages
Added the necessary build infrastructure for building packages
compatible with the Arch Linux distribution. As such, one can now run:
$ ./configure
$ make pkg # Alternatively, one can run 'make arch' as well
on an Arch Linux machine to create two binary packages compatible with
the pacman package manager, one for the spl userland utilties and
another for the spl kernel modules. The new packages can then be
installed by running:
# pacman -U $package.pkg.tar.xz
In addition, source-only packages suitable for an Arch Linux chroot
environment or remote builder can also be built using the 'sarch' make
rule.
NOTE: Since the source dist tarball is created on the fly from the head
of the build tree, it's MD5 hash signature will be continually influx.
As a result, the md5sum variable was intentionally omitted from the
PKGBUILD files, and the '--skipinteg' makepkg option is used. This may
or may not have any serious security implications, as the source tarball
is not being downloaded from an outside source.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Closes: #68
Prakash Surya [Tue, 6 Dec 2011 18:11:36 +0000 (10:11 -0800)]
Exercise new taskq interface in splat-taskq tests
The splat-taskq test functions were slightly modified to exercise
the new taskq interface in addition to the old interface. If the
old interface passes each of its tests, the new interface is
exercised. Both sub tests (old interface and new interface) must
pass for each test as a whole to pass.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #65
Prakash Surya [Tue, 6 Dec 2011 18:04:51 +0000 (10:04 -0800)]
Implement taskq_dispatch_prealloc() interface
This patch implements the taskq_dispatch_prealloc() interface which
was introduced by the following illumos-gate commit. It allows for
a preallocated taskq_ent_t to be used when dispatching items to a
taskq. This eliminates a memory allocation which helps minimize
lock contention in the taskq when dispatching functions.
Prakash Surya [Tue, 6 Dec 2011 17:48:06 +0000 (09:48 -0800)]
Add Test: "Single task queue, recursive dispatch"
Added another splat taskq test to ensure tasks can be recursively
submitted to a single task queue without issue. When the
taskq_dispatch_prealloc() interface is introduced, this use case
can potentially cause a deadlock if a taskq_ent_t is dispatched
while its tqent_list field is not empty. This _should_ never be
a problem with the existing taskq_dispatch() interface.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #65
Prakash Surya [Tue, 6 Dec 2011 01:32:48 +0000 (17:32 -0800)]
Replace tq_work_list and tq_threads in taskq_t
To lay the ground work for introducing the taskq_dispatch_prealloc()
interface, the tq_work_list and tq_threads fields had to be replaced
with new alternatives in the taskq_t structure.
The tq_threads field was replaced with tq_thread_list. Rather than
storing the pointers to the taskq's kernel threads in an array, they are
now stored as a list. In addition to laying the ground work for the
taskq_dispatch_prealloc() interface, this change could also enable taskq
threads to be dynamically created and destroyed as threads can now be
added and removed to this list relatively easily.
The tq_work_list field was replaced with tq_active_list. Instead of
keeping a list of taskq_ent_t's which are currently being serviced, a
list of taskq_threads currently servicing a taskq_ent_t is kept. This
frees up the taskq_ent_t's tqent_list field when it is being serviced
(i.e. now when a taskq_ent_t is being serviced, it's tqent_list field
will be empty).
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #65
Prakash Surya [Fri, 11 Nov 2011 23:06:35 +0000 (15:06 -0800)]
Replace struct spl_task with struct taskq_ent
The spl_task structure was renamed to taskq_ent, and all of
its fields were renamed to have a prefix of 'tqent' rather
than 't'. This was to align with the naming convention which
the ZFS code assumes. Previously these fields were private
so the name never mattered.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #65
Prakash Surya [Mon, 12 Dec 2011 23:37:30 +0000 (15:37 -0800)]
Fix usage of MUTEX macro in mutex_enter_nested
A call site of the MUTEX macro had incorrectly placed its closing
parenthesis, causing two parameters to be passed rather than one. This
change moves the misplaced parenthesis to fix the typographical error.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #70
Chris Dunlop [Tue, 6 Dec 2011 04:29:58 +0000 (15:29 +1100)]
Allow 64-bit timestamps to be set on 64-bit kernels
ZFS and 64-bit linux are perfectly capable of dealing with 64-bit
timestamps, but ZFS deliberately prevents setting them. Adjust
the SPL such that TIMESPEC_OVERFLOW will not always assume 32-bit
values and instead use the correct values for your kernel build.
This effectively allows 64-bit timestamps on 64-bit systems.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes ZFS issue #487
Prakash Surya [Fri, 18 Nov 2011 22:27:37 +0000 (14:27 -0800)]
Fix a typo referencing an incorrect symbol
The splat_taskq_test4_common function was incorrectly referencing
the splat_taskq-test13_func symbol, when it meant to be using the
splat_taskq_test4_func symbol.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #61
Brian Behlendorf [Fri, 11 Nov 2011 17:03:31 +0000 (09:03 -0800)]
Prepend spl_ to all init/fini functions
This is a bit of cleanup I'd been meaning to get to for a while
to reduce the chance of a type conflict. Well that conflict
finally occurred with the kstat_init() function which conflicts
with a function in the 2.6.32-6-pve kernel.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #56
Brian Behlendorf [Thu, 10 Nov 2011 18:36:21 +0000 (10:36 -0800)]
Fix depmod warning
The depmod utility from module-init-tools 3.12-pre3 generates a
warning when the -e option is used without -E or -F. This was
observed under OpenSuse 11.4. To resolve the issue when the
exact System.map-* for your kernel cannot be found fallback to
a generic safe '/sbin/depmod -a'.
WARNING: -e needs -E or -F
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Thu, 10 Nov 2011 00:31:03 +0000 (16:31 -0800)]
Linux 3.1 compat, shrink_*cache_memory
As of Linux 3.1 the shrink_dcache_memory and shrink_icache_memory
functions have been removed. This same task is now accomplished
more cleanly with per super block shrinkers. This unfortunately
leaves us no easy way to support the dnlc_reduce_cache() function.
This support has always been entirely optional. So when no
reasonable interface is available allow the dnlc_reduce_cache()
function to effectively become a no-op.
The downside of this change is that it will prevent the zfs arc
meta data limts from being enforced. However, the current zfs
implementation in this regard is already flawed and needs to
be reworked. If the arc needs to enfore a meta data limit it
will need to be extended to coordinate directly with the zpl.
This will allow us to drop all this compatibility code and get
more fine grained control over the cache management.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #52
Preferentially use the vfs_fsync() function. This function was
initially introduced in 2.6.29 and took three arguments. As
of 2.6.35 the dentry argument was dropped from the function.
For older kernels fall back to using file_fsync() which also
took three arguments including the dentry.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #52
Prior to Linux 3.1 the kern_path_parent symbol was exported for
use by kernel modules. As of Linux 3.1 it is now longer easily
available. To handle this case the spl will now dynamically
look up address of the missing symbol at module load time.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #52
Be careful not to unconditionally clear the PF_MEMALLOC bit in
the task structure. It may have already been set when entering
kv_alloc() in which case it must remain set on exit. In
particular the kswapd thread will have PF_MEMALLOC set in
order to prevent it from entering direct reclaim. By clearing
it we allow the following NULL deref to potentially occur.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff8109c7ab>] balance_pgdat+0x25b/0x4ff
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes ZFS issue #287
Gunnar Beutner [Tue, 18 Oct 2011 00:54:35 +0000 (02:54 +0200)]
Remove the spinlocks for mutex_enter()/mutex_exit()
The m_owner variable is protected by the mutex itself. Reading the variable
is guaranteed to be atomic (due to it being a word-sized reference) and
ACCESS_ONCE() takes care of read cache effects.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Gunnar Beutner [Tue, 18 Oct 2011 00:32:50 +0000 (02:32 +0200)]
Fix race condition in mutex_exit()
On kernels with CONFIG_DEBUG_MUTEXES mutex_exit() clears the mutex
owner after releasing the mutex. This would cause mutex_owner()
to return an incorrect owner if another thread managed to lock the
mutex before mutex_exit() had a chance to clear the owner.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes ZFS issue #167
Gunnar Beutner [Wed, 12 Oct 2011 10:49:18 +0000 (12:49 +0200)]
vn_rdwr() didn't properly advance the file position
This would cause problems when using 'zfs send' with a file as the
target (rather than a pipe or a socket as is usually the case) as
for each write the destination offset in the file would be 0.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes ZFS issue #391
Gunnar Beutner [Tue, 11 Oct 2011 17:03:29 +0000 (10:03 -0700)]
Fixed typo in spl_slab_alloc()
The typo did not have any effect (apart from a negligible performance
impact) because skc->skc_flags * KMC_OFFSLAB is always non-null when
at least one bit in skc->skc_flags is set.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
projects / spl / log