Chris Dunlop [Thu, 4 Oct 2012 06:19:17 +0000 (16:19 +1000)]
Switch KM_SLEEP to KM_PUSHPAGE
This warning indicates the incorrect use of KM_SLEEP in a call
path which must use KM_PUSHPAGE to avoid deadlocking in direct
reclaim. See commit b8d06fc for additional details.
SPL: Fixing allocation for task txg_sync (6093) which
used GFP flags 0x297bda7c with PF_NOFS set
Signed-off-by: Chris Dunlop <chris@onthe.net.au> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #1002
Reviewed by: Christopher Siden <chris.siden@delphix.com>
Reviewed by: Adam H. Leventhal <ahl@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Approved by: Eric Schrock <eric.schrock@delphix.com>
Ported-by: Etienne Dechamps <etienne.dechamps@ovh.net> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #995
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Matt Ahrens <matthew.ahrens@delphix.com>
Reviewed by: Christopher Siden <chris.siden@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Approved by: Dan McDonald <danmcd@nexenta.com>
error: Pool 'ztest' has encountered an uncorrectable I/O failure
and the failure mode property for this pool is set to panic.
We know how to fix it (see issue #939), but it may take some time
before we get around to merging the fix, which has some heavy
dependencies.
In the mean time, it is not ideal to be unable to use ztest just
because of a small isolated issue, so this patch works around the
problem by disabling the reguid test. This is just a temporary hack to
keep ztest usable.
The reguid test will be enabled again when the proper fix is merged.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #997
This worked fine until 40b84e7aec6392187722e61e5a4a853b530bf60f, which
changed path to be a pointer to the heap instead of an array allocated
on the stack. Before this change, sizeof(path) would return the size of
the array; now, it returns the size of the pointer instead.
As a result, the aforementioned sprintf statement uses the wrong size
and truncates the vdev file path to the first 4 or 8 bytes (depending
on the architecture). Typically, with default settings, the file path
will become "/tmp/zt" instead of "/test/ztest.XXX".
This issue only exists in ztest_vdev_attach_detach() and
ztest_fault_inject(), which explains why ztest doesn't fail right away.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #989
Currently, for unknown reasons, VOP_CLOSE() is a no-op in userspace.
This causes file descriptor leaks. This is especially problematic with
long ztest runs, since zpool.cache is opened repeatedly and never
closed, resulting in resource exhaustion (EMFILE errors).
This patch fixes the issue by making VOP_CLOSE() do what it is supposed
to do.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #989
Currently, thread_create(), when called in userspace, creates a
joinable (i.e. not detached thread). This is the pthread default.
Unfortunately, this does not reproduce kthreads behavior (kthreads
are always detached). In addition, this contradicts the original
Solaris code which creates userspace threads in detached mode.
These joinable threads are never joined, which leads to a leakage of
pthread thread objects ("zombie threads"). This in turn results in
excessive ressource consumption, and possible ressource exhaustion in
extreme cases (e.g. long ztest runs).
This patch fixes the issue by creating userspace threads in detached
mode. The only exception is ztest worker threads which are meant to be
joinable.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #989
Brian Behlendorf [Sun, 26 Aug 2012 20:38:06 +0000 (03:38 +0700)]
Modify vdev_elevator_switch() to use elevator_change()
As of Linux 2.6.36 an elevator_change() interface was added.
This commit updates vdev_elevator_switch() to use this interface
when available, otherwise it falls back to the usermodehelper
method.
Original-patch-by: foobarz <sysop@xeon.(none)> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #906
Currently, mkfs.ext2 on zconfig.sh zvols tries to use a 8K blocksize,
probably because by default zvol exposes an optimal I/O size of 8K.
Unfortunately, a ext2 blocksize of 8K is not supported by the kernel,
so the resulting filesystem is unmountable.
This patch fixes the issue by making sure the blocksize is 4K. We have
to use -F to force it else mkfs.ext2 won't allow us to use a blocksize
smaller than the optimal I/O size.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #979
In order to implement synchronous NFS metadata semantics ZFS
needs to provide the .commit_metadata hook. All it takes there
is to make sure changes are committed to ZIL. Fortunately
zfs_fsync() does just that, so simply calling it from
zpl_commit_metadata() does the trick.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #969
Bill Pijewski [Wed, 9 May 2012 22:05:14 +0000 (15:05 -0700)]
Illumos #2703: add mechanism to report ZFS send progress
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
https://www.illumos.org/issues/2703
Ported by: Martin Matuska <martin@matuska.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Chris Siden [Tue, 24 Jan 2012 02:43:32 +0000 (18:43 -0800)]
Illumos #1948: zpool list should show more detailed pool info
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Albert Lee <trisk@nexenta.com>
Reviewed by: Dan McDonald <danmcd@nexenta.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Approved by: Eric Schrock <eric.schrock@delphix.com>
References:
https://www.illumos.org/issues/1948
Ported by: Martin Matuska <martin@matuska.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #685
Brian Behlendorf [Wed, 19 Sep 2012 18:50:22 +0000 (11:50 -0700)]
Switch KM_SLEEP to KM_PUSHPAGE
This warning indicates the incorrect use of KM_SLEEP in a call
path which must use KM_PUSHPAGE to avoid deadlocking in direct
reclaim. See commit b8d06fca089fae4680c3a552fc55c512bfb02202
for additional details.
SPL: Fixing allocation for task txg_sync (6093) which
used GFP flags 0x297bda7c with PF_NOFS set
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #973
Brian Behlendorf [Sat, 15 Sep 2012 20:25:21 +0000 (13:25 -0700)]
Improve `zpool import` search behavior
The goal of this change is to make 'zpool import' prefer to use
the peristent /dev/mapper or /dev/disk/by-* paths. These are far
preferable to the devices in /dev/ whos names are not persistent
and are determined by the order in which a device is detected.
This patch improves things by changing the default search path from
just to the top level /dev/ directory to (in order):
/dev/disk/by-vdev - Custom rules, use first if they exist
/dev/disk/zpool - Custom rules, use first if they exist
/dev/mapper - Use multipath devices before components
/dev/disk/by-uuid - Single unique entry and persistent
/dev/disk/by-id - May be multiple entries and persistent
/dev/disk/by-path - Encodes physical location and persistent
/dev/disk/by-label - Custom persistent labels
/dev - UNSAFE device names will change
The default search path can be overriden by setting the
ZPOOL_IMPORT_PATH environment variable. This must be a colon
delimited list of paths which are searched for vdevs. If the
'zpool import -d' option is specified only those listed paths
will be searched.
Finally, when multiple paths to the same device are found. If one
of the paths is an exact match for the path used last time to import
the pool it will be used. When there are no exact matches the
prefered path will be determined by the provided search order.
This means you can still import a pool and force specific names by
providing the -d <path> option. And the prefered names will persist
as long as those paths exist on your system.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #965
Brian Behlendorf [Mon, 17 Sep 2012 18:22:23 +0000 (11:22 -0700)]
Switch KM_SLEEP to KM_PUSHPAGE
This warning indicates the incorrect use of KM_SLEEP in a call
path which must use KM_PUSHPAGE to avoid deadlocking in direct
reclaim. See commit b8d06fca089fae4680c3a552fc55c512bfb02202
for additional details.
SPL: Fixing allocation for task txg_sync (6093) which
used GFP flags 0x297bda7c with PF_NOFS set
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #917
When zfs_replay_write() replays TX_WRITE records from ZIL
it calls zpl_write_common() to perform the actual write.
zpl_write_common() returns the number of bytes written
(similar to write() system call) or an (negative) error.
However, the code expects the positive return value to be
a residual counter. Thus when zpl_write_common() successfully
completes it is mistakenly considered to be a partial write and
the error code delivered further. At this point the ZIL processing
is aborted with famous "ZFS replay transaction error 5" error
message given to the message buffer.
The fix is to compare the zpl_write_commmon() return value with
the buffer size and flag error only when they disagree.
Signed-off-by: Cyril Plisko <cyril.plisko@mountall.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #933
The error handing code for the dmu_tx_assign() failure case
relied on there always being a registered commit callback to
clear the PG_writeback bit. Since that is no longer strictly
true for the synchronous case we must explicitly invoke the
callback.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #961
Brian Behlendorf [Wed, 12 Sep 2012 18:16:08 +0000 (11:16 -0700)]
Move iput() after zfs_inode_update()
When replaying an unlink/remove operation via zfs_rmdir() the object
being removed will be instantiated by a call to zfs_dirent_lock().
This means that there is a single reference protecting the object.
Right before the call to zfs_inode_update() this reference is dropped
which may cause the object to be destroyed. This will result in a
NULL dereference as shown by the stack trace is issue #782.
This likely isn't an issue during normal operation because there is
always an additional reference held on the object by the VFS.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #782
Pools using AF drives which were originally created with a sector
size of 512 bytes will now be correctly detected to have physical
sector size of 4096. This is desirable for a new pool, however for
an existing pool abruptly changing the sector size causes problems.
For this reason, this change is being reverted until the additional
logic can be added to detect the existing pool case. Existing
pools must use the ashift size stored in the label regardless of
what the disk reports. This is critical for compatibility.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #955
Silence "setting dataset to sync always" message in ztest.
ztest outputs a message when testing sync=always no matter what the
verbosity level is. There is no point outputting this message for low
verbosity levels.
With this patch the message is only displayed at verbosity level 5 or
above. The result is less output pollution.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #951
The 'zfs destroy' changes in 330d06f disrupted how zvol devices
get removed on ZoL. However, it basically boils down to the
fact that we are no longer reliably calling zvol_remove_minor()
via zfs_ioc_destroy_snaps().
Therefore we add the missing call and handle things similarly
to the existing zfs_unmount_snap() case. Ideally we would check
if this is of type DMU_OST_ZFS or DMU_OST_ZVOL and just do the
right thing as in zfs_ioc_destroy(). However, it looks like
it would be fairly expensive to get the type, and it's harmless
to simply attempt the umount and minor removal.
This is also an issue in the latest FreeBSD and Illumos code.
It was being tracked under the following issue, and we may want
to refresh our code when they settle on what they want to do
about it upstream.
https://www.illumos.org/issues/3170
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #903
Unfortunately, due to differences in how the stack is used in userspace
vs kernel space, spurious stack overflows could occur in userspace
tools due to the limited stack size. This is especially true in ztest
when debugging is enabled.
This patch multiplies the userspace stack size by 4, which fixes the
stack overflow issues. This comes at the price of not being able to
catch stack size issues in userspace, but the previous solution proved
unreliable anyway.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Fixes #934.
Buffers for the ARC are normally backed by the SPL virtual slab.
However, if memory is low, AND no slab objects are available,
AND a new slab cannot be quickly constructed a new emergency
object will be directly allocated.
These objects can be as large as order 5 on a system with 4k
pages. And because they are allocated with KM_PUSHPAGE, to
avoid a potential deadlock, they are not allowed to initiate I/O
to satisfy the allocation. This can result in the occasional
allocation failure.
However, since these allocations are allowed to block and
perform operations such as memory compaction they will eventually
succeed. Since this is not unexpected (just unlikely) behavior
this patch disables the warning for the allocation failure.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #465
Michael Martin [Wed, 5 Sep 2012 16:46:29 +0000 (09:46 -0700)]
Fix missing vdev names in zpool status output
Commit 858219c makes more sense down below in the 'if (verbose)'
section of the code. Initially, buf and path will never point
to the same location. Once 'path = buf' is set on a raidz vdev,
the code may drop into the verbose section depending on the
verbose flag. In here, using a tmpbuf makes sense since now
'buf == path'.
This issue does not occur in the upstream Solaris code because
their implementations of snprintf() allow for buf and path to
be the same address.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #57
This warning indicates the incorrect use of KM_SLEEP in a call
path which must use KM_PUSHPAGE to avoid deadlocking in direct
reclaim. See commit b8d06fca089fae4680c3a552fc55c512bfb02202
for additional details.
SPL: Fixing allocation for task txg_sync (6093) which
used GFP flags 0x297bda7c with PF_NOFS set
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #917
This warning indicates the incorrect use of KM_SLEEP in a call
path which must use KM_PUSHPAGE to avoid deadlocking in direct
reclaim. See commit b8d06fca089fae4680c3a552fc55c512bfb02202
for additional details.
SPL: Fixing allocation for task txg_sync (6093) which
used GFP flags 0x297bda7c with PF_NOFS set
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #917
Use the bdev_physical_block_size() interface to determine the
minimize write size which can be issued without incurring a
read-modify-write operation. This is used to set the ashift
correctly to prevent a performance penalty when using AF hard
disks.
Unfortunately, this interface isn't entirely reliable because
it's not uncommon for disks to misreport this value. For this
reason you may still need to manually set your ashift with:
zpool create -o ashift=12 ...
The solution to this in the upstream Illumos source was to add
a while list of known offending drives. Maintaining such a list
will be a burden, but it still may be worth doing if we can
detect a large number of these drives. This should be considered
as future work.
Reported-by: Richard Yao <ryao@cs.stonybrook.edu> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #916
This warning indicates the incorrect use of KM_SLEEP in a call
path which must use KM_PUSHPAGE to avoid deadlocking in direct
reclaim. See commit b8d06fca089fae4680c3a552fc55c512bfb02202
for additional details.
SPL: Fixing allocation for task txg_sync (6093) which
used GFP flags 0x297bda7c with PF_NOFS set
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #917
Commit e6f290535c2fff8b940c4eacb1c90cbc2cfc7508 added libzpool to
the mount_zfs dependencies. This brought in the nvpair symbols
which are used by libzpool. To resolve this include the libnvpair
library for mount_zfs even though mount_zfs doesn't directly
require any of these symbols.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #926
Chris Dunlop [Sat, 1 Sep 2012 04:44:13 +0000 (14:44 +1000)]
Switch KM_SLEEP to KM_PUSHPAGE
This warning indicates the incorrect use of KM_SLEEP in a call
path which must use KM_PUSHPAGE to avoid deadlocking in direct
reclaim. See commit b8d06fca089fae4680c3a552fc55c512bfb02202
for additional details.
SPL: Fixing allocation for task txg_sync (6093) which
used GFP flags 0x297bda7c with PF_NOFS set
Signed-off-by: Chris Dunlop <chris@onthe.net.au> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #917
Brian Behlendorf [Fri, 31 Aug 2012 14:45:27 +0000 (07:45 -0700)]
Switch KM_SLEEP to KM_PUSHPAGE
This warning indicates the incorrect use of KM_SLEEP in a call
path which must use KM_PUSHPAGE to avoid deadlocking in direct
reclaim. See commit b8d06fca089fae4680c3a552fc55c512bfb02202
for additional details.
SPL: Fixing allocation for task txg_sync (6093) which
used GFP flags 0x297bda7c with PF_NOFS set
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #917
Brian Behlendorf [Wed, 29 Aug 2012 18:52:47 +0000 (11:52 -0700)]
Clear PG_writeback after zil_commit() for sync I/O
When writing via ->writepage() the writeback bit was always cleared
as part of the txg commit callback. However, when the I/O is also
being written synchronsously to the zil we can immediately clear this
bit. There is no need to wait for the subsequent TXG sync since the
data is already safe on stable storage.
This has been observed to reduce the msync(2) delay from up to 5
seconds down 10s of miliseconds. One workload which is expected
to benefit from this are the intermittent samba hands described
in issue #700.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #700
Closes #907
Etienne Dechamps [Thu, 30 Aug 2012 10:15:10 +0000 (12:15 +0200)]
Fix mount_zfs dependency on libzpool.
mount_zfs depends on libzpool for zfs_prop_written since 330d06f90d143b41b276796526a66a1c1fff046d. Unfortunately, the Makefile
for mount_zfs has not been modified to reflect this. As a result,
libtool doesn't know about the dependency, which may result in the wrong
libzpool being used during the build (e.g. the libzpool from the system
instead of the libzpool from the build directory).
This patch adds the dependency to fix the issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Fixes #909.
Richard Yao [Mon, 7 May 2012 17:49:51 +0000 (13:49 -0400)]
Switch KM_SLEEP to KM_PUSHPAGE
Differences between how paging is done on Solaris and Linux can cause
deadlocks if KM_SLEEP is used in any the following contexts.
* The txg_sync thread
* The zvol write/discard threads
* The zpl_putpage() VFS callback
This is because KM_SLEEP will allow for direct reclaim which may result
in the VM calling back in to the filesystem or block layer to write out
pages. If a lock is held over this operation the potential exists to
deadlock the system. To ensure forward progress all memory allocations
in these contexts must us KM_PUSHPAGE which disables performing any I/O
to accomplish the memory allocation.
Previously, this behavior was acheived by setting PF_MEMALLOC on the
thread. However, that resulted in unexpected side effects such as the
exhaustion of pages in ZONE_DMA. This approach touchs more of the zfs
code, but it is more consistent with the right way to handle these cases
under Linux.
This is patch lays the ground work for being able to safely revert the
following commits which used PF_MEMALLOC:
21ade34 Disable direct reclaim for z_wr_* threads cfc9a5c Fix zpl_writepage() deadlock eec8164 Fix ASSERTION(!dsl_pool_sync_context(tx->tx_pool))
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #726
Brian Behlendorf [Wed, 22 Aug 2012 03:53:01 +0000 (20:53 -0700)]
mzap_upgrade() must use kmem_alloc()
These allocations in mzap_update() used to be kmem_alloc() but
were changed to vmem_alloc() due to the size of the allocation.
However, since it turns out this function may be called in the
context of the txg_sync thread they must be changed back to use
a kmem_alloc() to ensure the KM_PUSHPAGE flag is honored.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Sat, 18 Aug 2012 18:17:23 +0000 (11:17 -0700)]
Annotate KM_PUSHPAGE call paths with PF_NOFS
The txg_sync(), zfs_putpage(), zvol_write(), and zvol_discard()
call paths must only use KM_PUSHPAGE to avoid potential deadlocks
during direct reclaim.
This patch annotates these call paths so any accidental use of
KM_SLEEP will be quickly detected. In the interest of stability
if debugging is disabled the offending allocation will have its
GFP flags automatically corrected. When debugging is enabled
any misuse will be treated as a fatal error.
This patch is entirely for debugging. We should be careful to
NOT become dependant on it fixing up the incorrect allocations.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Mon, 20 Aug 2012 00:17:02 +0000 (17:17 -0700)]
Pre-allocate vdev I/O buffers
The vdev queue layer may require a small number of buffers
when attempting to create aggregate I/O requests. Rather than
attempting to allocate them from the global zio buffers, which
is slow under memory pressure, it makes sense to pre-allocate
them because...
1) These buffers are short lived. They are only required for
the life of a single I/O at which point they can be used by
the next I/O.
2) The maximum number of concurrent buffers needed by a vdev is
small. It's roughly limited by the zfs_vdev_max_pending tunable
which defaults to 10.
By keeping a small list of these buffer per-vdev we can ensure
one is always available when we need it. This significantly
reduces contention on the vq->vq_lock, because we no longer
need to perform a slow allocation under this lock. This is
particularly important when memory is already low on the system.
It would probably be wise to extend the use of these buffers beyond
aggregate I/O and in to the raidz implementation. The inability
to quickly allocate buffer for the parity stripes could result in
similiar problems.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Richard Yao [Wed, 16 May 2012 22:16:02 +0000 (18:16 -0400)]
Revert Disable direct reclaim for z_wr_* threads
This commit used PF_MEMALLOC to prevent a memory reclaim deadlock.
However, commit 49be0ccf1fdc2ce852271d4d2f8b7a9c2c4be6db eliminated
the invocation of __cv_init(), which was the cause of the deadlock.
PF_MEMALLOC has the side effect of permitting pages from ZONE_DMA
to be allocated. The use of PF_MEMALLOC was found to cause stability
problems when doing swap on zvols. Since this technique is known to
cause problems and no longer fixes anything, we revert it.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #726
Richard Yao [Mon, 7 May 2012 18:14:45 +0000 (14:14 -0400)]
Revert Fix zpl_writepage() deadlock
The commit, cfc9a5c88f91f7b4d606fce89505e1f404691ea5, to fix deadlocks
in zpl_writepage() relied on PF_MEMALLOC. That had the effect of
disabling the direct reclaim path on all allocations originating from
calls to this function, but it failed to address the actual cause of
those deadlocks. This led to the same deadlocks being observed with
swap on zvols, but not with swap on the loop device, which exercises
this code.
The use of PF_MEMALLOC also had the side effect of permitting
allocations to be made from ZONE_DMA in instances that did not require
it. This contributes to the possibility of panics caused by depletion
of pages from ZONE_DMA.
As such, we revert this patch in favor of a proper fix for both issues.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #726
Commit eec8164771bee067c3cd55ed0a16dadeeba276de worked around an issue
involving direct reclaim through the use of PF_MEMALLOC. Since we
are reworking thing to use KM_PUSHPAGE so that swap works, we revert
this patch in favor of the use of KM_PUSHPAGE in the affected areas.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #726
Prakash Surya [Fri, 24 Aug 2012 18:37:44 +0000 (11:37 -0700)]
Remove autoconf check for CONFIG_PREEMPT
The autoconf macro which failed if CONFIG_PREEMPT was set in the kernel
config was removed. With the inclusion of a few previous patches
targeting support for preempt enabled kernels, it is now safe to run
with this kernel config option enabled.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #83
Brian Behlendorf [Sat, 25 Aug 2012 22:01:39 +0000 (15:01 -0700)]
rmdir(2) should return ENOTEMPTY
Under Solaris the behavior for rmdir(2) is to return EEXIST when
a directory still contains entries. However, on Linux ENOTEMPTY
is the expected return value with EEXIST being technically allowed.
According to rmdir(2):
ENOTEMPTY
pathname contains entries other than . and .. ; or, pathname has
.. as its final component. POSIX.1-2001 also allows EEXIST for
this condition.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #895
Richard Yao [Sat, 25 Aug 2012 22:32:54 +0000 (18:32 -0400)]
Check kernel source directory for SPL
ZFS fails to build when SPL is built into the kernel on unless
--with-spl=/path/to/kernel/sources is specified. We fallback to the
kernel sources directory when SPL is not found elsewhere to resolve
that.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closed #896
Javen Wu [Sat, 25 Aug 2012 02:24:48 +0000 (19:24 -0700)]
Drop spill buffer reference
When calling sa_update() and friends it is possible that a spill
buffer will be needed to accomidate the update. When this happens
a hold is taken on the new dbuf and that hold must be released
before calling dmu_tx_commit(). Failing to release the hold will
cause a copy of the dbuf to be made in dbuf_sync_leaf(). This is
done to ensure further updates to the dbuf never sneak in to the
syncing txg.
This could be left to the sa_update() caller. But then the caller
would need to be aware of this internal SA implementation detail.
It is therefore preferable to handle this all internally in the
SA implementation.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #503
Closes #513
Brian Behlendorf [Fri, 24 Aug 2012 03:46:38 +0000 (20:46 -0700)]
Revert "Use SA_HDL_PRIVATE for SA xattrs"
This reverts commit ec2626ad3f695a2ced3946c4197ef64cbcac4959 which
caused consistency problems between the shared and private handles.
Reverting this change should resolve issues #709 and #727. It
will also reintroduce an arc_anon memory leak which is addressed
by the next commit.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #709
Closes #727
Prakash Surya [Fri, 24 Aug 2012 00:45:31 +0000 (17:45 -0700)]
Wrap smp_processor_id in kpreempt_[dis|en]able
After surveying the code, the few places where smp_processor_id is used
were deemed to be safe to use with a preempt enabled kernel. As such, no
core logic had to be changed. These smp_processor_id call sites are simply
are wrapped in kpreempt_disable and kpreempt_enabled to prevent the
Linux kernel from emitting scary warnings.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Issue #83
Massimo Maggi [Thu, 23 Aug 2012 12:52:45 +0000 (14:52 +0200)]
Fix snapshot automounting with GrSecurity constify plugin.
./configure erroneously detects absence of dops->d_automount
when built against a GrSecurity patched kernel.
Summerized error message found in config.log:
checking whether dops->d_automount() exists
...
In function 'main': ... error: constified variable 'dops'
cannot be local
The "dops" variable cannot be a local variable, so it's
moved to the global scope.
This test also fails if the prototype of the dops->d_automount
function pointer is changed.
Signed-off-by: Massimo Maggi <massimo@mmmm.it> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Closes #884
Garrett D'Amore [Wed, 6 Jun 2012 17:01:43 +0000 (10:01 -0700)]
Illumos #2803: zfs get guid pretty-prints the output
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Richard Elling <richard.elling@gmail.com>
Reviewed by: Alexander Eremin <alexander.eremin@nexenta.com>
Approved by: Dan McDonald <danmcd@nexenta.com>
References:
https://www.illumos.org/issues/2803
Ported by: Martin Matuska <martin@matuska.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
1796 "ZFS HOLD" should not be used when doing "ZFS SEND" from a read-only pool
2871 support for __ZFS_POOL_RESTRICT used by ZFS test suite
2903 zfs destroy -d does not work
2957 zfs destroy -R/r sometimes fails when removing defer-destroyed snapshot
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
Eric Schrock [Fri, 27 Apr 2012 18:14:46 +0000 (11:14 -0700)]
Illumos #2635: 'zfs rename -f' to perform force unmount
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: George Wilson <George.Wilson@delphix.com>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/2635
Ported by: Martin Matuska <martin@matuska.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #717
Martin Matuska [Tue, 21 Aug 2012 21:42:00 +0000 (23:42 +0200)]
Properly initialize and free destroydata
This regression was accidentally introduced by commit 330d06f90d143b41b276796526a66a1c1fff046d due to ZoL
specific code. The fix is to simply ensure the passed
nvlist is initialized and freed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #876
Brian Behlendorf [Tue, 14 Aug 2012 15:35:32 +0000 (08:35 -0700)]
Export dmu_buf_rele() symbol
While I'd like to remove the various pragmas in module/zfs/dbuf.c.
There are consumers such as Lustre which still depend on dmu_buf_*
versions of the symbols. Until all consumers can be converted to
use only the dbuf_* names leave this symbol exported.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Mon, 13 Aug 2012 22:47:18 +0000 (15:47 -0700)]
Cleanly remove zfs-modules-devel headers
Add the /usr/src/zfs-<version>-<release>/<kernel> directory to
the zfs-modules-devel package. This ensures that this directory
will be removed when the package is removed.
We do not include the higher level /usr/src/zfs-<version>-<release>
directory since there may be builds for multiple kernels. Instead,
a %postun rmdir is added which attempts to remove this directory.
It will only succeed when the last zfs-modules-devel-* package
for this specific release is removed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Fri, 10 Aug 2012 23:39:39 +0000 (16:39 -0700)]
Suppress 'zfs_sb_create' memory warning
When mutex debugging is enabled in your kernel the increased
size of the mutex structures can push the zfs_sb_t type beyond
the 8k warning threshold. This isn't harmful so we suppress
the warning for this case.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #628
Brian Behlendorf [Fri, 10 Aug 2012 23:30:13 +0000 (16:30 -0700)]
Illumos #1888: zfs(8) should mention zfs recv -e
Reviewed by: Garrett D'Amore <garrett@damore.org>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Gordon Ross <gordon.w.ross@gmail.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/1888
Ported by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #683
zfs.spec.in defines %_prefix as /, so man pages end up getting
installed in /share/man on RPM 4.9 systems. To fix this, define
%_mandir relative to %_datadir in the spec file.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #353
Prakash Surya [Tue, 7 Aug 2012 20:13:17 +0000 (13:13 -0700)]
Support building a zfs-modules-dkms sub package
This commit adds support for building a zfs-modules-dkms sub package
built around Dynamic Kernel Module Support. This is to allow building
packages using the DKMS infrastructure which is intended to ease the
burden of kernel version changes, upgrades, etc.
By default zfs-modules-dkms-* sub package will be built as part of
the 'make rpm' target. Alternately, you can build only the DKMS
module package using the 'make rpm-dkms' target.
Examples:
# To build packaged binaries as well as a dkms packages
$ ./configure && make rpm
# To build only the packaged binary utilities and dkms packages
$ ./configure && make rpm-utils rpm-dkms
Note: Only the RHEL 5/6, CHAOS 5, and Fedora distributions are
supported for building the dkms sub package.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #535
Prakash Surya [Wed, 8 Aug 2012 00:07:55 +0000 (17:07 -0700)]
Add '--with-spl-timeout' option
When checking for the SPL Module.symvers file, a timeout can now be
passed in which will pause the configure step while it waits for this
file to be generated. By default, the configure behavior is unchanged as
a timeout of 0 is used. If a positive number of seconds is passed,
configure will wait that number of seconds for the Module.symvers file
before moving on.
The main motivation for this change was to support parallel execution of
'./configure && make' for the SPL and ZFS packages in preparation of
supporting DKMS based packages.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Dan McDonald [Tue, 15 Nov 2011 19:01:27 +0000 (14:01 -0500)]
Illumos #1693: persistent 'comment' field for a zpool
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/1693
Ported by: Martin Matuska <martin@matuska.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #678
Currently, zvols have a discard granularity set to 0, which suggests to
the upper layer that discard requests of arbirarily small size and
alignment can be made efficiently.
In practice however, ZFS does not handle unaligned discard requests
efficiently: indeed, it is unable to free a part of a block. It will
write zeros to the specified range instead, which is both useless and
inefficient (see dnode_free_range).
With this patch, zvol block devices expose volblocksize as their discard
granularity, so the upper layer is aware that it's not supposed to send
discard requests smaller than volblocksize.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #862
Richard Yao [Sun, 29 Jul 2012 09:43:57 +0000 (05:43 -0400)]
Add missing dependencies to ./copy-builtin
ZFS depends on EFI_PARTITION, ZLIB_DEFLATE and ZLIB_INFLATE, but when
ZFS is integrated with the kernel source tree, menuconfig does not
enforce these dependencies. This can cause build failures in the case of
ZLIB_DEFLATE and ZLIB_INFLATE where symbols are not found. This can also
cause runtime failures in the case of EFI_PARTITION, where the kernel
will not understand GPT partitions when creating pools from raw disks.
We solve this by making menuconfig aware of these dependencies.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #854
The number of blocks that can be discarded in one BLKDISCARD ioctl on a
zvol is currently unlimited. Some applications, such as mkfs, discard
the whole volume at once and they use the maximum possible discard size
to do that. As a result, several gigabytes discard requests are not
uncommon.
Unfortunately, if a large amount of data is allocated in the zvol, ZFS
can be quite slow to process discard requests. This is especially true
if the volblocksize is low (e.g. the 8K default). As a result, very
large discard requests can take a very long time (seconds to minutes
under heavy load) to complete. This can cause a number of problems, most
notably if the zvol is accessed remotely (e.g. via iSCSI), in which case
the client has a high probability of timing out on the request.
This patch solves the issue by adding a new tunable module parameter:
zvol_max_discard_blocks. This indicates the maximum possible range, in
zvol blocks, of one discard operation. It is set by default to 16384
blocks, which appears to be a good tradeoff. Using the default
volblocksize of 8K this is equivalent to 128 MB. When using the maximum
volblocksize of 128K this is equivalent to 2 GB.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #858
Matthew Ahrens [Thu, 17 Nov 2011 18:14:36 +0000 (10:14 -0800)]
Illumos #1644, #1645, #1646, #1647, #1708
1644 add ZFS "clones" property
1645 add ZFS "written" and "written@..." properties
1646 "zfs send" should estimate size of stream
1647 "zfs destroy" should determine space reclaimed by
destroying multiple snapshots
1708 adjust size of zpool history data
This commit modifies the user to kernel space ioctl ABI. Extra
care should be taken when updating to ensure both the kernel
modules and utilities are updated. This change has reordered
all of the new ioctl()s to the end of the list. This should
help minimize this issue in the future.
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Albert Lee <trisk@opensolaris.org>
Approved by: Garrett D'Amore <garret@nexenta.com>
Ported by: Martin Matuska <martin@matuska.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #826
Closes #664
Brian Behlendorf [Mon, 30 Jul 2012 22:38:02 +0000 (15:38 -0700)]
Allow '-o remount' for non-legacy datasets
This is done for compatibility with existing Linux infrastructure.
In particular, when using zfs as a root filesystem there are init
scripts which as part of shutdown remount root read-only. Also,
the new systemd infrastructure being used by Fedora expects to be
able to remount a file system read-write.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #847
Brian Behlendorf [Thu, 26 Jul 2012 22:37:13 +0000 (15:37 -0700)]
Merge branch 'builtin-clean'
Support in-tree builtin module building.
These commits add support for compiling the ZFS module as a built-in
kernel module by copying the module code into the kernel source tree.
Here's the procedure:
- Create your kernel configuration (`.config` file) as usual. This
has to be done first so that ZFS's configure script is able to
detect kernel features correctly.
- Run `make prepare scripts` inside the kernel source tree.
- Run `./configure --enable-linux-builtin --with-linux=/usr/src/linux-...`
inside the ZFS directory.
- Run `./copy-builtin /usr/src/linux-...` inside the ZFS directory.
- In the kernel source tree, enable the `CONFIG_ZFS` option (e.g. using
`make menuconfig`). Note that this option depends on `CONFIG_SPL`
(see zfsonlinux/spl@744038069d3dc65e721b5b8cc5c37d8c7fcbd8c0).
- Build the kernel as usual.
ZFS module parameters can be set at boot time using the following syntax
on the kernel command line: `zfs.parameter_name=parameter_value`.
When libzfs checks if the module is loaded or not, it currently reads
/proc/modules and searches for a line matching the module name.
Unfortunately, if the module is included in the kernel itself (built-in
module), then /proc/modules won't list it, so libzfs will wrongly conclude
that the module is not loaded, thus making all ZFS userspace tools unusable.
Fortunately, all loaded modules appear as directories in /sys/module, even
built-in ones. Thus we can use /sys/module in lieu of /proc/modules to fix
the issue.
As a bonus, the code for checking becomes much simpler.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #851
This commit introduces a "copy-builtin" script designed to prepare a
kernel source tree for building ZFS as a builtin module. The script
makes a full copy of all needed files, thus making the kernel source
tree fully independent of the zfs source package.
To achieve that, some compilation flags (-include, -I) have been moved
to module/Makefile. This Makefile is only used when compiling external
modules; when compiling builtin modules, a Kbuild file generated by the
configure-builtin script is used instead. This makes sure Makefiles
inside the kernel source tree does not contain references to the zfs
source package.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #851
This patch adds a new autoconf function: ZFS_LINUX_TRY_COMPILE_SYMBOL.
This new function does the following:
- Call LINUX_TRY_COMPILE with the specified parameters.
- If unsuccessful, return false.
- If successful and we're configuring with --enable-linux-builtin,
return true.
- Else, call CHECK_SYMBOL_EXPORT with the specified parameters and
return the result.
All calls to CHECK_SYMBOL_EXPORT are converted to
LINUX_TRY_COMPILE_SYMBOL so that the tests work even when configuring
for builtin on a kernel which doesn't have loadable module support, or
hasn't been built yet.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #851
Currently, when building a test case, we're compiling an entire Linux
module from beginning to end. This includes the MODPOST stage, which
generates a "conftest.mod.c" file with some boilerplate module
declaration code.
This poses a problem when configuring for built-in on kernels which have
loadable module support disabled. In this case conftest.mod.c is
referencing disabled code, resulting in a compilation failure, thus
breaking the tests.
This patch fixes the issue by faking the modpost stage when the
--enable-linux-builtin option is provided. It does so by forcing the
modpost command to be /bin/true, and using an empty conftest.mod.c file.
The test module still compiles fine, although the result isn't loadable,
but we don't really care at this point.
Note it is important to preserve the modpost stage when building out of
tree. The ZFS_AC_KERNEL_BLK_END_REQUEST, ZFS_AC_KERNEL_BLK_QUEUE_FLUSH,
and ZFS_AC_KERNEL_BLK_RQ_BYTES configure checks all depend on it to
identify GPL-only symbols.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #851
This patch adds a new option to configure: --enable-linux-builtin. When
this option is used, the following happens:
- Compilation of kernel modules is disabled.
- A failure to find UTS_RELEASE is followed by a suggestion to run
"make prepare" on the kernel source tree.
This patch also adds a new test which tries to compile an empty module
as a basic toolchain sanity test. If it fails and the option was
specified, the error is followed by a suggestion to run "make scripts"
on the kernel source tree.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #851
Currently, when configure --with-config is used, selective compilation
is only effective for the simple "make" case. Package builders (e.g.
make rpm) still build everything (utils and modules). This patch fixes
that.
Signed-off-by: Prakash Surya <surya1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #851
Richard Yao [Mon, 23 Jul 2012 18:39:25 +0000 (11:39 -0700)]
Linux 3.5 compat, end_writeback() changed to clear_inode()
The end_writeback() function was changed by moving the call to
inode_sync_wait() earlier in to evict(). This effecitvely changes
the ordering of the sync but it does not impact the details of
the zfs implementation.
However, as part of this change end_writeback() was renamed to
clear_inode() to reflect the new semantics. This change does
impact us and clear_inode() now maps to end_writeback() for
kernels prior to 3.5.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #784
Richard Yao [Mon, 23 Jul 2012 17:55:48 +0000 (10:55 -0700)]
Linux 3.5 compat, eops->encode_fh() takes inodes
The export_operations member ->encode_fh() has been updated to
take both the child and parent inodes. This interface used to
take the child dentry and a bool describing if the parent is needed.
NOTE: While updating this code I noticed that we do not currently
cleanly handle the case where we're passed a connectable parent.
This code should be audited to make sure we're doing the right thing.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
Richard Yao [Thu, 19 Jul 2012 22:37:56 +0000 (18:37 -0400)]
Fix NULL pointer dereference on PaX/GRSecurity patched Linux 3.3 and later kernels
Support for PaX/GRSecurity patched kernels was developed against Linux
3.2. Unfortunately, an autotools check introduced for a Linux 3.3 API
fails on PaX/GRSecurity patched kernels. This causes the module to be
built against the Linux 3.2 ABI, which results in a NULL pointer
dereference at runtime.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Closes #794
Closes #809
Brian Behlendorf [Thu, 19 Jul 2012 21:50:25 +0000 (14:50 -0700)]
Disable .zfs directory on 32-bit systems
The .zfs control directory implementation currently relies on
the fact that there is a direct 1:1 mapping from an object id
to its inode number. This works well as long as the system
uses a 64-bit value to store the inode number.
Unfortunately, the Linux kernel defines the inode number as
an 'unsigned long' type. This means that for 32-bit systems
will only have 32-bit inode numbers but we still have 64-bit
object ids.
This problem is particularly acute for the .zfs directories
which leverage those upper 32-bits. This is done to avoid
conflicting with object ids which are allocated monotonically
starting from 0. This is likely to also be a problem for
datasets on 32-bit systems with more than ~2 billion files.
The right long term fix must remove the simple 1:1 mapping.
Until that's done the only safe thing to do is to disable the
.zfs directory on 32-bit systems.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Thu, 19 Jul 2012 21:50:25 +0000 (14:50 -0700)]
Add ddt_object_load() error handling
Add the missing error handling to ddt_object_load(). There's no
good reason this needs to be fatal. It is preferable that an
error be returned. This will allow 'zpool import -FX' to safely
attempt to rollback through previous txgs looking for a good one.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
projects / zfs / log