This commit adds module options for all existing zfs tunables.
Ideally the average user should never need to modify any of these
values. However, in practice sometimes you do need to tweak these
values for one reason or another. In those cases it's nice not to
have to resort to rebuilding from source. All tunables are visable
to modinfo and the list is as follows:
$ modinfo module/zfs/zfs.ko
filename: module/zfs/zfs.ko
license: CDDL
author: Sun Microsystems/Oracle, Lawrence Livermore National Laboratory
description: ZFS
srcversion: 8EAB1D71DACE05B5AA61567
depends: spl,znvpair,zcommon,zunicode,zavl
vermagic: 2.6.32-131.0.5.el6.x86_64 SMP mod_unload modversions
parm: zvol_major:Major number for zvol device (uint)
parm: zvol_threads:Number of threads for zvol device (uint)
parm: zio_injection_enabled:Enable fault injection (int)
parm: zio_bulk_flags:Additional flags to pass to bulk buffers (int)
parm: zio_delay_max:Max zio millisec delay before posting event (int)
parm: zio_requeue_io_start_cut_in_line:Prioritize requeued I/O (bool)
parm: zil_replay_disable:Disable intent logging replay (int)
parm: zfs_nocacheflush:Disable cache flushes (bool)
parm: zfs_read_chunk_size:Bytes to read per chunk (long)
parm: zfs_vdev_max_pending:Max pending per-vdev I/Os (int)
parm: zfs_vdev_min_pending:Min pending per-vdev I/Os (int)
parm: zfs_vdev_aggregation_limit:Max vdev I/O aggregation size (int)
parm: zfs_vdev_time_shift:Deadline time shift for vdev I/O (int)
parm: zfs_vdev_ramp_rate:Exponential I/O issue ramp-up rate (int)
parm: zfs_vdev_read_gap_limit:Aggregate read I/O over gap (int)
parm: zfs_vdev_write_gap_limit:Aggregate write I/O over gap (int)
parm: zfs_vdev_scheduler:I/O scheduler (charp)
parm: zfs_vdev_cache_max:Inflate reads small than max (int)
parm: zfs_vdev_cache_size:Total size of the per-disk cache (int)
parm: zfs_vdev_cache_bshift:Shift size to inflate reads too (int)
parm: zfs_scrub_limit:Max scrub/resilver I/O per leaf vdev (int)
parm: zfs_recover:Set to attempt to recover from fatal errors (int)
parm: spa_config_path:SPA config file (/etc/zfs/zpool.cache) (charp)
parm: zfs_zevent_len_max:Max event queue length (int)
parm: zfs_zevent_cols:Max event column width (int)
parm: zfs_zevent_console:Log events to the console (int)
parm: zfs_top_maxinflight:Max I/Os per top-level (int)
parm: zfs_resilver_delay:Number of ticks to delay resilver (int)
parm: zfs_scrub_delay:Number of ticks to delay scrub (int)
parm: zfs_scan_idle:Idle window in clock ticks (int)
parm: zfs_scan_min_time_ms:Min millisecs to scrub per txg (int)
parm: zfs_free_min_time_ms:Min millisecs to free per txg (int)
parm: zfs_resilver_min_time_ms:Min millisecs to resilver per txg (int)
parm: zfs_no_scrub_io:Set to disable scrub I/O (bool)
parm: zfs_no_scrub_prefetch:Set to disable scrub prefetching (bool)
parm: zfs_txg_timeout:Max seconds worth of delta per txg (int)
parm: zfs_no_write_throttle:Disable write throttling (int)
parm: zfs_write_limit_shift:log2(fraction of memory) per txg (int)
parm: zfs_txg_synctime_ms:Target milliseconds between tgx sync (int)
parm: zfs_write_limit_min:Min tgx write limit (ulong)
parm: zfs_write_limit_max:Max tgx write limit (ulong)
parm: zfs_write_limit_inflated:Inflated tgx write limit (ulong)
parm: zfs_write_limit_override:Override tgx write limit (ulong)
parm: zfs_prefetch_disable:Disable all ZFS prefetching (int)
parm: zfetch_max_streams:Max number of streams per zfetch (uint)
parm: zfetch_min_sec_reap:Min time before stream reclaim (uint)
parm: zfetch_block_cap:Max number of blocks to fetch at a time (uint)
parm: zfetch_array_rd_sz:Number of bytes in a array_read (ulong)
parm: zfs_pd_blks_max:Max number of blocks to prefetch (int)
parm: zfs_dedup_prefetch:Enable prefetching dedup-ed blks (int)
parm: zfs_arc_min:Min arc size (ulong)
parm: zfs_arc_max:Max arc size (ulong)
parm: zfs_arc_meta_limit:Meta limit for arc size (ulong)
parm: zfs_arc_reduce_dnlc_percent:Meta reclaim percentage (int)
parm: zfs_arc_grow_retry:Seconds before growing arc size (int)
parm: zfs_arc_shrink_shift:log2(fraction of arc to reclaim) (int)
parm: zfs_arc_p_min_shift:arc_c shift to calc min/max arc_p (int)
Every distribution has slightly different requirements for their
init scripts. Because of this the zfs package contains several
init scripts for various distributions. These scripts have been
contributed by, and are supported by, the larger zfs community.
Init scripts for Gentoo/Lunar/Redhat have been contributed by:
When a new znode/inode pair is created both the znode and the inode
should be immediately updated to the correct values. This was done
for the znode and for most of the values in the inode, but not all
of them. This normally wasn't a problem because most subsequent
operations would cause the inode to be immediately updated. This
change ensures the inode is now fully updated before it is inserted
in to the inode hash.
Brian Behlendorf [Fri, 25 Feb 2011 07:36:01 +0000 (14:36 +0700)]
Fix 'zfs set volsize=N pool/dataset'
This change fixes a kernel panic which would occur when resizing
a dataset which was not open. The objset_t stored in the
zvol_state_t will be set to NULL when the block device is closed.
To avoid this issue we pass the correct objset_t as the third arg.
The code has also been updated to correctly notify the kernel
when the block device capacity changes. For 2.6.28 and newer
kernels the capacity change will be immediately detected. For
earlier kernels the capacity change will be detected when the
device is next opened. This is a known limitation of older
kernels.
Online ext3 resize test case passes on 2.6.28+ kernels:
$ dd if=/dev/zero of=/tmp/zvol bs=1M count=1 seek=1023
$ zpool create tank /tmp/zvol
$ zfs create -V 500M tank/zd0
$ mkfs.ext3 /dev/zd0
$ mkdir /mnt/zd0
$ mount /dev/zd0 /mnt/zd0
$ df -h /mnt/zd0
$ zfs set volsize=800M tank/zd0
$ resize2fs /dev/zd0
$ df -h /mnt/zd0
Original-patch-by: Fajar A. Nugraha <github@fajar.net>
Closes #68
Closes #84
Brian Behlendorf [Fri, 29 Apr 2011 21:03:12 +0000 (14:03 -0700)]
Correct MAXUID
The uid_t on most systems is in fact and unsigned 32-bit value.
This is almost always correct, however you could compile your
kernel to use an unsigned 16-bit value for uid_t. In practice
I've never encountered a distribution which does this so I'm
willing to overlook this corner case for now.
Brian Behlendorf [Wed, 27 Apr 2011 16:32:51 +0000 (09:32 -0700)]
Suppress 'vdev_metaslab_init' memory warning
The vdev_metaslab_init() function has been observed to allocate
larger than 8k chunks. However, they are not much larger than 8k
and it does this infrequently so it is allowed and the warning is
supressed.
Brian Behlendorf [Tue, 26 Apr 2011 21:56:04 +0000 (14:56 -0700)]
Conserve stack in dsl_scan_visit()
The dsl_scan_visit() function is a little heavy weight taking 464
bytes on the stack. This can be easily reduced for little cost by
moving zap_cursor_t and zap_attribute_t off the stack and on to the
heap. After this change dsl_scan_visit() has been reduced in size
by 320 bytes.
This change was made to reduce stack usage in the dsl_scan_sync()
callpath which is recursive and has been observed to overflow the
stack.
Brian Behlendorf [Tue, 26 Apr 2011 22:43:07 +0000 (15:43 -0700)]
Conserve stack in dsl_scan_visitbp()
This function is called recursively so everything possible must be
done to limit its stack consumption. The dprintf_bp() debugging
function adds 30 bytes of local variables to the function we cannot
afford. By commenting out this debugging we save 30 bytes per
recursion and depths of 13 are not uncommon. This yeilds a total
stack saving of 390 bytes on our 8k stack.
Brian Behlendorf [Fri, 22 Apr 2011 17:12:49 +0000 (10:12 -0700)]
Conserve stack in dsl_scan_visitbp()
The recursive call chain dsl_scan_visitbp() -> dsl_scan_recurse() ->
dsl_scan_visitdnode() -> dsl_scan_visitbp has been observed to consume
considerable stack resulting in a stack overflow (>8k). The cleanest
way I see to fix this with minimal impact to the existing flow of
code, and with the fewest performance concerns, is to always inline
dsl_scan_recurse() and dsl_scan_visitdnode(). While this will increase
the function size of dsl_scan_visitbp(), by 4660 bytes, it also reduces
the stack requirements by removing the function call overhead.
Brian Behlendorf [Tue, 26 Apr 2011 19:56:35 +0000 (12:56 -0700)]
Fix zvol deadlock
It's possible for a zvol_write thread to enter direct memory reclaim
while holding open a transaction group. This results in the system
attempting to write out data to the disk to free memory. Unfortunately,
this can't succeed because the the thread doing reclaim is holding open
the txg which must be closed to be synced to disk. To prevent this
the offending allocation is marked KM_PUSHPAGE which will prevent it
from attempting writeback.
Disable the gethostid() override for Solaris behavior because Linux systems
implement the POSIX standard in a way that allows a negative result.
Mask the gethostid() result to the lower four bytes, like coreutils does in
/usr/bin/hostid, to prevent junk bits or sign-extension on systems that have an
eight byte long type. This can cause a spurious hostid mismatch that prevents
zpool import on 64-bit systems.
Brian Behlendorf [Fri, 22 Apr 2011 23:21:26 +0000 (16:21 -0700)]
Fix 32-bit MAXOFFSET_T definition
Having MAXOFFSET_T defined to 0x7fffffffl was artificially limiting
the maximum file size on 32-bit systems. In reality MAXOFFSET_T is
used when working with 'long long' types and as such we now define
it as LLONG_MAX. This resolves the 2GB file size limit for files
and additionally allows zvols greater than 2GB on 32-bit systems.
Brian Behlendorf [Fri, 22 Apr 2011 20:50:17 +0000 (13:50 -0700)]
Fix spurious -EFAULT when setting I/O scheduler
Occasionally we would see an -EFAULT returned when setting the
I/O scheduler on a vdev. This was caused an improperly formatted
user mode helper command.
This commit restructures the command to something simpler, allocates
space for it dynamically to save stack, and removes the retry logic
which is no longer needed.
Brian Behlendorf [Thu, 31 Mar 2011 01:59:17 +0000 (18:59 -0700)]
Enforce ARC meta-data limits
This change ensures the ARC meta-data limits are enforced. Without
this enforcement meta-data can grow to consume all of the ARC cache
pushing out data and hurting performance. The cache is aggressively
reclaimed but this is a soft and not a hard limit. The cache may
exceed the set limit briefly before being brought under control.
By default 25% of the ARC capacity can be used for meta-data. This
limit can be tuned by setting the 'zfs_arc_meta_limit' module option.
Once this limit is exceeded meta-data reclaim will occur in 3 percent
chunks, or may be tuned using 'arc_reduce_dnlc_percent'.
Gunnar Beutner [Thu, 14 Apr 2011 20:07:24 +0000 (22:07 +0200)]
Fixed a use-after-free bug in zfs_zget().
Fixed a bug where zfs_zget could access a stale znode pointer when
the inode had already been removed from the inode cache via iput ->
iput_final -> ... -> zfs_zinactive but the corresponding SA handle
was still alive.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #180
Brian Behlendorf [Wed, 20 Apr 2011 17:18:56 +0000 (10:18 -0700)]
Suppress 'zfs receive' memory warning
As part of zfs_ioc_recv() a zfs_cmd_t is allocated in the kernel
which is 17808 bytes in size. This sort of thing in general should
be avoided. However, since this should be an infrequent event for
now we allow it and simply suppress the warning with the KM_NODEBUG
flag. This can be revisited latter if/when it becomes an issue.
Brian Behlendorf [Tue, 19 Apr 2011 23:14:15 +0000 (16:14 -0700)]
Update zconfig.sh to use new zvol names
This change should have occured when we commited the new udev
rules for zvols. Basically, the test script is just out of date.
We need to update it to use the /dev/zvol/ device names, and
to expect the more common -partN suffixes.
I added a udev_trigger() call in zconfig_partition() and
zconfig_zvol_device_stat() to ensure that all the udev rules have
run before. This ensures the devices are available to subsequent
commands and closes a small race.
Finally, I was forced added a small 'sleep 1' to test 10. I
was observing occassional failures in my VM due to the device
still claiming to be busy. Delaying betwen the various methods
of adding/removing a vdev avoids the issue.
Brian Behlendorf [Tue, 19 Apr 2011 22:01:37 +0000 (15:01 -0700)]
Add parted and lsscsi dependencies to zfs-test
The zfault.sh and zconfig.sh test scripts requires the parted
utility, the lsscsi utility, and the scsi_debug module. To
ensure the utilities are available they have been added as
dependencies to zfs-test package. Checking for scsi_debug
is a little more problematic because if it's missing you will
need to build it. For clarity the documention has been updated
to mention this.
Gunnar Beutner [Sun, 17 Apr 2011 17:42:33 +0000 (19:42 +0200)]
Added missing initialization for va.va_dentry in zfs_get_xattrdir.
Without this we may mistakenly believe we have a dentry and try to
d_instantiate() it. This will result in the following BUG. It's
important to note that while the xattr directory has an inode
assoicated with it we never create a dentry for it.
kernel BUG at fs/dcache.c:1418!
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #202
Brian Behlendorf [Tue, 19 Apr 2011 17:39:31 +0000 (10:39 -0700)]
Set -Wno-unused-but-set-variable globally
As of gcc-4.6 the option -Wunused-but-set-variable is enabled by
default. While this is a useful warning there are numerous places
in the ZFS code when a variable is set and then only checked in an
ASSERT(). To avoid having to update every instance of this in the
code we now set -Wno-unused-but-set-variable to suppress the warning.
Additionally, when building with --enable-debug and -Werror set these
warning also become fatal. We can reevaluate the suppression of these
error at a later time if it becomes an issue. For now we are basically
just reverting to the previous gcc behavior.
Brian Behlendorf [Tue, 19 Apr 2011 17:02:21 +0000 (10:02 -0700)]
Fix gcc configure warnings
Newer versions of gcc are getting smart enough to detect the sloppy
syntax used for the autoconf tests. It is now generating warnings
for unused/undeclared variables. Newer version of gcc even have
the -Wunused-but-set-variable option set by default. This isn't a
problem except when -Werror is set and they get promoted to an error.
In this case the autoconf test will return an incorrect result which
will result in a build failure latter on.
To handle this I'm tightening up many of the autoconf tests to
explicitly mark variables as unused to suppress the gcc warning.
Remember, all of the autoconf code can never actually be run we
just want to get a clean build error to detect which APIs are
available. Never using a variable is absolutely fine for this.
Brian Behlendorf [Mon, 18 Apr 2011 23:44:22 +0000 (16:44 -0700)]
Fix gcc compiler warning, parse_option()
When compiling ZFS in user space gcc-4.6.0 correctly identifies
the variable 'value' as being set but never used. This generates a
warning and a build failure when using --enable-debug. Once again
this is correct but I'm reluctant to remove 'value' because we are
breaking the string in to name/value pairs. While it is not used
now there's a good chance it will be soon and I'd rather not have
to reinvent this. To suppress the warning with just as a VERIFY().
This was observed under Fedora 15.
cmd/mount_zfs/mount_zfs.c: In function ‘parse_option’:
cmd/mount_zfs/mount_zfs.c:112:21: error: variable ‘value’ set but not
used [-Werror=unused-but-set-variable]
Brian Behlendorf [Mon, 18 Apr 2011 23:27:45 +0000 (16:27 -0700)]
Fix gcc compiler warning, dsl_pool_create()
When compiling ZFS in user space gcc-4.6.0 correctly identifies
the variable 'os' as being set but never used. This generates a
warning and a build failure when using --enable-debug. However,
the code is correct we only want to use 'os' for the kernel space
builds. To suppress the warning the call was wrapped with a
VERIFY() which has the nice side effect of ensuring the 'os'
actually never is NULL. This was observed under Fedora 15.
module/zfs/dsl_pool.c: In function ‘dsl_pool_create’:
module/zfs/dsl_pool.c:229:12: error: variable ‘os’ set but not used
[-Werror=unused-but-set-variable]
Brian Behlendorf [Mon, 18 Apr 2011 21:12:28 +0000 (14:12 -0700)]
Linux 2.6.39 compat, invalidate_inodes()
Update code to use the spl_invalidate_inodes() wrapper. This hides
some of the complexity of determining if invalidate_inodes() was
exported, and if so what is its prototype. The second argument
of spl_invalidate_inodes() determined the behavior of how dirty
inodes are handled. By passing a zero we are indicated that we
want those inodes to be treated as busy and skipped.
Brian Behlendorf [Mon, 18 Apr 2011 19:48:44 +0000 (12:48 -0700)]
Autogen refresh for kernel-insert-inode-locked.m4
Several Makefile.in's were accidentally not updated when the
kernel-insert-inode-locked.m4 check was added. This change simply
refreshes the missed files.
When rebuilding the source RPM under el5 you need to append the
target_cpu. However, under el6/ch5 things are packaged correctly
and the arch is already part of kver. For this reason it also
needs to be stripped from kver when setting kverpkg.
The .sync_fs fix as applied did not use the updated SPL credential
API. This broke builds on Debian Lenny, this change applies the
needed fix to use the portable API. The original credential changes
are part of commit 81e97e21872a9c38ad66c37fafe1436ee25abee3.
Apply all of Rudd-O's changes for the Fedora init script. The
initial init script was one I threw together based on Rudd-O's
original work. It worked for me but it has some flaws.
Rudd-O has invested considerable time updating it to be significantly
smarter. It now handles using ZFS as your root filesystem plus
various other quirks. Since he is familiar with the right
way to do things on Fedora and has tested this init script we
are integrating all of his changes.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Disable the normal reclaim path for the txg_sync thread. This
ensures the thread will never enter dmu_tx_assign() which can
otherwise occur due to direct reclaim. If this is allowed to
happen the system can deadlock. Direct reclaim call path:
Brian Behlendorf [Wed, 30 Mar 2011 01:08:59 +0000 (18:08 -0700)]
Add direct+indirect ARC reclaim
Under OpenSolaris all memory reclaim is done asyncronously. Under
Linux memory reclaim is done asynchronously _and_ synchronously.
When a process allocates memory with GFP_KERNEL it explicitly allows
the kernel to do reclaim on its behalf to satify the allocation.
If that GFP_KERNEL allocation fails the kernel may take more drastic
measures to reclaim the memory such as killing user space processes.
This was observed to happen with ZFS because the ARC could consume
a large fraction of the system memory but no synchronous reclaim
could be performed on it. The result was GFP_KERNEL allocations
could fail resulting in OOM events, and only moments latter the
arc_reclaim thread would free unused memory from the ARC.
This change leaves the arc_thread in place to manage the fundamental
ARC behavior. But it adds a synchronous (direct) reclaim path for
the ARC which can be called when memory is badly needed. It also
adds an asynchronous (indirect) reclaim path which is called
much more frequently to prune the ARC slab caches.
Brian Behlendorf [Wed, 30 Mar 2011 06:04:39 +0000 (23:04 -0700)]
Call d_instantiate before unlocking inode
Under Linux a dentry referencing an inode must be instantiated before
the inode is unlocked. To accomplish this without overly modifing
the core ZFS code the dentry it passed via the vattr_t. There are
cases such as replay when a dentry is not available. In which case
it is obviously not initialized at inode creation time, if a dentry
is needed it will be spliced as when required via d_lookup().
Fix `make distclean` for `./configure --with-config=user
Making distclean in module
make[1]: Entering directory `/zfs/module'
make -C SUBDIRS=`pwd` clean
make: Entering an unknown directory
make: *** SUBDIRS=/zfs/module: No such file or directory. Stop.
When using --with-config=user the 'distclean' target would fail
because it assumes the kernel configuration infrastrure is set up.
This is not the case, nor does it need to be, because the
'--with-config=user' option will prune the entire ./module subtree
from SUBDIRS. This prevents most build rules from operating in the
./module directory.
However, the 'dist*' rules will still traverse this directory
because it is listed in DIST_SUBDIRS. This is correct because we
need to ensure the dist rules package the directory contents
regardless of the configuration for the 'dist' rule. The correct
way to handle this is to only invoke the kernel build system as
part of the 'clean' rule when CONFIG_KERNEL_TRUE is set.
Initial fix provided by Darik Horn <dajhorn@vanadac.com>.
This commit is a slightly refined form of the original.
Ned Bass [Fri, 1 Apr 2011 16:47:05 +0000 (09:47 -0700)]
Call udevadm trigger more safely
Some udev hooks are not designed to be idempotent, so calling udevadm
trigger outside of the distribution's initialization scripts can have
unexpected (and potentially dangerous) side effects. For example, the
system time may change or devices may appear multiple times. See Ubuntu
launchpad bug 320200 and this mailing list post for more details:
To avoid these problems we call udevadm trigger with --action=change
--subsystem-match=block. The first argument tells udev just to refresh
devices, and make sure everything's as it should be. The second
argument limits the scope to block devices, so devices belonging to
other subsystems cannot be affected.
This doesn't fix the problem on older udev implementations that don't
provide udevadm but instead have udevtrigger as a standalone program.
In this case the above options aren't available so there's no way to
call call udevtrigger safely. But we can live with that since this
issue only exists in optional test and helper scripts, and most
zfs-on-linux users are running newer systems anyways.
Brian Behlendorf [Thu, 31 Mar 2011 20:43:49 +0000 (13:43 -0700)]
Update CHAOS 5 Packaging
The CHAOS 5 kernels are now packaged identially to the RHEL6 kernels.
Therefore we can simply use the RHEL6 rules in the spec file when
building packages.
Brian Behlendorf [Thu, 31 Mar 2011 19:16:24 +0000 (12:16 -0700)]
Fix libzpool cv_* build error
This build failure was accidentally introduced by previous commit bfd214a which fixed the load average. Unfortunately, the wrapper
for cv_wait_interruptible was not available in the zfs_context.h
user compatibility code. I failed to notice this because I didn't
rebuild everything cleanly before committing.
undefined reference to `cv_wait_interruptible'
collect2: ld returned 1 exit status
Kernel threads which sleep uninterruptibly on Linux are marked in the (D)
state. These threads are usually in the process of performing IO and are
thus counted against the load average. The txg_quiesce and txg_sync threads
were always sleeping uninterruptibly and thus inflating the load average.
This change makes them sleep interruptibly. Some care is required however
because these threads may now be woken early by signals. In this case the
callers are all careful to check that the required conditions are met after
waking up. If we're woken early due to a signal they will simply go back
to sleep. In this case these changes are safe.
Fajar A. Nugraha [Fri, 25 Mar 2011 17:01:28 +0000 (10:01 -0700)]
Spec file compat, %{datadir}
The dracut change caused an error during "make rpm". The cause
is simple, RHEL5 does not recognize the %{datarootdir} macro in
zfs.spec. It was changed to %{datadir} which fixes the build.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Thu, 24 Mar 2011 18:34:41 +0000 (11:34 -0700)]
Set cmd paths in udev rules using --prefix
The udev/rules.d scripts must use absolute paths to their support
binaries. However, where those binaries get installed depends
on what --prefix was set to when the package was configured.
This change makes the udev/rules.d helpers to *.in files which
are processed by configure. This allows them to be dynamically
updated to include the specified --prefix.
Additionally, this change updates 60-zvol.rules to handle both
the 'add' and 'change' actions. This ensures that that all
valid zvol devices are correctly linked.
Fajar A. Nugraha [Thu, 24 Mar 2011 08:22:52 +0000 (15:22 +0700)]
Fixes to enable zvol symlink creation
This commit fixes issue on
https://github.com/behlendorf/zfs/issues/#issue/172
Changes:
- update BLKZNAME to use _IOR instead of _IO. Kernel 2.6.32 allows
read parameters (copy_to_user) with _IO, while newer kernels (tested
Archlinux's 2.6.37 kernel) enforces _IOR (which is correct)
- fix return code and message on error
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Tue, 22 Mar 2011 18:22:49 +0000 (11:22 -0700)]
Linux 2.6.29 compat, .freeze_fs/.unfreeze_fs
The .freeze_fs/.unfreeze_fs hooks were not added until Linux 2.6.29
Since these hooks are currently unused they are being removed to
allow support of older kernels.
Brian Behlendorf [Tue, 22 Mar 2011 18:13:41 +0000 (11:13 -0700)]
Linux 2.6.29 compat, credentials
As of Linux 2.6.29 a clean credential API was added to the Linux kernel.
Previously the credential was embedded in the task_struct. Because the
SPL already has considerable support for handling this API change the
ZPL code has been updated to use the Solaris credential API.
Brian Behlendorf [Tue, 22 Mar 2011 16:55:09 +0000 (09:55 -0700)]
Linux 2.6.28 compat, insert_inode_locked()
Added insert_inode_locked() helper function, prior to this most callers
used insert_inode_hash(). The older method doesn't check for collisions
in the inode_hashtable but it still acceptible for use. Fallback to
using insert_inode_hash() when insert_inode_locked() is unavailable.
Brian Behlendorf [Tue, 22 Mar 2011 16:26:38 +0000 (09:26 -0700)]
Linux 2.6.27 compat, blk_queue_stackable()
The blk_queue_stackable() queue flag was added in 2.6.27 to handle dm
stacking drivers. Prior to this request stacking drivers were detected
by checking (q->request_fn == NULL), for earlier kernels we revert to
this legacy behavior.
Brian Behlendorf [Mon, 21 Mar 2011 23:54:59 +0000 (16:54 -0700)]
Linux compat, umount2(2) flags
Older glibc <sys/mount.h> headers did not define all the available
umount2(2) flags. Both MNT_FORCE and MNT_DETACH are supported in the
kernel back to 2.4.11 so we define them correctly if they are missing.
Brian Behlendorf [Mon, 21 Mar 2011 17:19:30 +0000 (10:19 -0700)]
Fix evict() deadlock
Now that KM_SLEEP is not defined as GFP_NOFS there is the possibility
of synchronous reclaim deadlocks. These deadlocks never existed in the
original OpenSolaris code because all memory reclaim on Solaris is done
asyncronously. Linux does both synchronous (direct) and asynchronous
(indirect) reclaim.
This commit addresses a deadlock caused by inode eviction. A KM_SLEEP
allocation may trigger direct memory reclaim and shrink the inode cache.
This can occur while a mutex in the array of ZFS_OBJ_HOLD mutexes is
held. Through the ->shrink_icache_memory()->evict()->zfs_inactive()->
zfs_zinactive() call path the same mutex may be reacquired resulting
in a deadlock. To avoid this deadlock the process must not reacquire
the mutex when it is already holding it.
This is a reasonable fix for now but longer term the ZFS_OBJ_HOLD
mutex locking should be reevaluated. This infrastructure already
prevents us from ever using the Linux lock dependency analysis tools,
and it may limit scalability.
Brian Behlendorf [Sat, 19 Mar 2011 21:34:30 +0000 (14:34 -0700)]
Use KM_PUSHPAGE instead of KM_SLEEP
It used to be the case that all KM_SLEEP allocations were GFS_NOFS.
Unfortunately this often resulted in the kernel being unable to
reclaim the ARC, inode, and dentry caches in a timely manor.
The fix was to make KM_SLEEP a GFP_KERNEL allocation in the SPL.
However, this increases the posibility of deadlocking the system
on a zfs write thread. If a zfs write thread attempts to perform
an allocation it may trigger synchronous reclaim. This reclaim
may attempt to flush dirty data/inode to disk to free memory.
Unforunately, this write cannot finish because the write thread
which would handle it is holding the previous transaction open.
Deadlock.
To avoid this all allocations in the zfs write thread path must
use KM_PUSHPAGE which prohibits synchronous reclaim for that
thread. In this way forward progress in ensured. The risk
with this change is I missed updating an allocation for the
write threads leaving an increased posibility of deadlock. If
any deadlocks remain they will be unlikely but we'll have to
make sure they all get fixed.
Brian Behlendorf [Fri, 18 Mar 2011 21:47:19 +0000 (14:47 -0700)]
Fix 'LDFLAGS=-Wl,--as-needed' build error
Compiling with 'LDFLAGS=-Wl,--as-needed' exposed the fact that
there were some library linking problems introduced by mount_zfs.
In particular, the libzfs library does use nvpair symbols, and
mount_zfs contains no dependencies on libzpool.
Brian Behlendorf [Fri, 18 Mar 2011 20:54:27 +0000 (13:54 -0700)]
Fix getcwd() warning
New versions glibc declare getcwd() with the warn_unused_result attribute.
This results in a warning because the updated mount helper was not
checking this return value. This issue was fixed by checking the return
type and in the case of an error simply returning the passed dataset.
One possible, but unlikely, error would be having your cwd directory
unlinked while the mount command was running.
cmd/mount_zfs/mount_zfs.c: In function ‘parse_dataset’:
cmd/mount_zfs/mount_zfs.c:223:2: error: ignoring return value of
‘getcwd’, declared with attribute warn_unused_result
To simplify the process of using zfs as your root filesystem a
zfs-drucat sub-package has been added. This sub-package adds a zfs
dracut module which allows your initramfs to be rebuilt with zfs
support. The process for doing this is still complicated but there
is clearly interest from the community about getting this working
well and documented. This should help lay some of the groundwork.
Longer term these changes should be pushed in the upstream dracut
package. Once that occurs this subpackage will no longer be
required for new systems, however we may want to conditionally
build this package in the future for systems running older
dracut versions.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Thu, 17 Mar 2011 22:02:28 +0000 (15:02 -0700)]
Add init scripts
To support automatically mounting your zfs on filesystem on boot
a basic init script is needed. Unfortunately, every distribution
has their own idea of the _right_ way to do things. Rather than
write one very complicated portable init script, which would be
invariably replaced by the distributions own anyway. I have
instead added support to provide multiple distribution specific
init scripts.
The correct init script for your distribution will be selected
by ZFS_AC_DEFAULT_PACKAGE which will set DEFAULT_INIT_SCRIPT.
During 'make install' the correct script for your system will
be installed from zfs/etc/init.d/zfs.DEFAULT_INIT_SCRIPT to the
usual /etc/init.d/zfs location.
Currently, there is zfs.fedora and a more generic zfs.lsb init
script. Hopefully, the distribution maintainers who know best
how they want their init scripts to function will feedback their
approved versions to be included in the project.
This change does not consider upstart jobs but I'm not at all
opposed to add that sort of thing.
Brian Behlendorf [Tue, 15 Mar 2011 19:41:19 +0000 (12:41 -0700)]
Register .remount_fs handler
Register the missing .remount_fs handler. This handler isn't strictly
required because the VFS does a pretty good job updating most of the
MS_* flags. However, there's no harm in using the hook to call the
registered zpl callback for various MS_* flags. Additionaly, this
allows us to lay the ground work for more complicated argument parsing
in the future.
Brian Behlendorf [Tue, 15 Mar 2011 19:03:42 +0000 (12:03 -0700)]
Register .sync_fs handler
Register the missing .sync_fs handler. This is a noop in most cases
because the usual requirement is that sync just be initiated. As part
of the DMU's normal transaction processing txgs will be frequently
synced. However, when the 'wait' flag is set the requirement is that
.sync_fs must not return until the data is safe on disk. With the
addition of the .sync_fs handler this is now properly implemented.
Brian Behlendorf [Tue, 15 Mar 2011 18:17:33 +0000 (11:17 -0700)]
Strip 'zfsutil,remount' from /etc/mtab
When updating /etc/mtab we should be careful and strip certain
options. In particular, we need to strip 'zfsutil' because if
we don't the mount utility will helpfull provide it to the
mount helper when we issue mount(8) again. This subverts the
check that the caller is zfs(8) and not mount(8).
Brian Behlendorf [Tue, 15 Mar 2011 16:34:56 +0000 (09:34 -0700)]
Always allow '-o remount,ro'
Allow the mount(8) utility to always operate on all datasets when
remounting them read-only. This critical for rc.sysinit/umountroot
which remounts the root filesystem read-only during shutdown to
ensure everything is correctly flushed to disk.
Fix minor typo, the check to set zfsutil should use the bitwise
'&'. I must have accidentally hit the adjacent '*' and obviously
neither the compiler or my code review caught this. Fix it now.
Brian Behlendorf [Thu, 10 Mar 2011 21:34:17 +0000 (13:34 -0800)]
Don't set I/O Scheduler for Partitions
ZFS should only change the i/o scheduler for a disk when it has
ownership of the whole disk. This is basically the same logic as
adjusting the write cache behavior on a disk. This change updates
the vdev disk code to skip partitions when setting the i/o scheduler.
Brian Behlendorf [Thu, 10 Mar 2011 20:58:44 +0000 (12:58 -0800)]
Check for trailing '/' in mount.zfs
When run with a root '/' cwd the mount.zfs helper would strip not
only the '/' but also the next character from the dataset name.
For example, '/tank' was changed to 'ank' instead of just 'tank'.
Originally, this was done for the '/tmp' cwd case where we needed
to strip the '/' following the cwd. For example '/tmp/tank' needed
to remove the '/tmp' cwd plus 1 character for the '/'.
This change fixes the problem by checking the cwd and if it ends in
a '/' it does not strip and extra character. Otherwise it will strip
the next character. I believe this should only ever be true for the
root directory.
Because we are dependent of the system mount/umount utilities to
ensure correct mtab locking, we should not suppress their error
output. During a successful mount/umount they will be silent,
but during a failure the error message they print is the only sure
way to know why a mount failed. This is because the (u)mount(8)
return code does not contain the result of the system call issued.
The only way to clearly idenify why thing failed is to rely on
the error message printed by the tool.
Longer term once libmount is available we can issue the mount/umount
system calls within the tool and still be ensured correct mtab locking.
Several issues related to strange mount/umount behavior were reported
and this commit should address most of them. The original idea was
to put in place a zfs mount helper (mount.zfs). This helper is used
to enforce 'legacy' mount behavior, and perform any extra mount argument
processing (selinux, zfsutil, etc). This helper wasn't ready for the
0.6.0-rc1 release but with this change it's functional but needs to
extensively tested.
This change addresses the following open issues.
Closes #101
Closes #107
Closes #113
Closes #115
Closes #119
Due to an uninitialized variable files opened with O_APPEND may
overwrite the start of the file rather than append to it. This
was introduced accidentally when I removed the Solaris vnodes.
The zfs_range_lock_writer() function used to key off zf->z_vnode
to determine if a znode_t was for a zvol of zpl object. With
the removal of vnodes this was replaced by the flag zp->z_is_zvol.
This flag was used to control the append behavior for range locks.
Unfortunately, this value was never properly initialized after
the vnode removal. However, because most of memory is usually
zeros it happened to be set correctly most of the time making
the bug appear racy. Properly initializing zp->z_is_zvol to
zero completely resolves the problem with O_APPEND.
Move 'bulk' and 'xattr_bulk' from the stack to the heap to minimize
stack space usage. These two arrays consumed 448 bytes on the stack
and have been replaced by two 8 byte points for a total stack space
saving of 432 bytes. The zfs_setattr() path had been previously
observed to overrun the stack in certain circumstances.
The original range lock implementation had to be modified by commit 8926ab7 because it was unsafe on Linux. In particular, calling
cv_destroy() immediately after cv_broadcast() is dangerous because
the waiters may still be asleep. Thus the following cv_destroy()
will free memory which may still be in use.
This was fixed by updating cv_destroy() to block on waiters but
this in turn introduced a deadlock. The deadlock was resolved
with the use of a taskq to move the offending free outside the
range lock. This worked well but using the taskq for the free
resulted in a serious performace hit. This is somewhat ironic
because at the time I felt using the taskq might improve things
by making the free asynchronous.
This patch refines the original fix and moves the free from the
taskq to a private free list. Then items which must be free'd
are simply inserted in to the list. When the range lock is dropped
it's safe to free the items. The list is walked and all rl_t
entries are freed.
This change improves small cached read performance by 26x. This
was expected because for small reads the number of locking calls
goes up significantly. More surprisingly this change significantly
improves large cache read performance. This probably attributable
to better cpu/memory locality. Very likely the same processor
which allocated the memory is now freeing it.
In the original implementation the zfs_open()/zfs_close() hooks
were dropped for simplicity. This was functional but not 100%
correct with the expected ZFS sematics. Updating and re-adding the
zfs_open()/zfs_close() hooks resolves the following issues.
1) The ZFS_APPENDONLY file attribute is once again honored. While
there are still no Linux tools to set/clear these attributes once
there are it should behave correctly.
2) Minimal virus scan file attribute hooks were added. Once again
this support in disabled but the infrastructure is back in place.
3) Most importantly correctly handle assigning files which were
opened syncronously to the intent log. Without this change O_SYNC
modifications could be lost during a system crash even though they
were marked synchronous.
Filesystems like ZFS must use what the kernel calls an anonymous super
block. Basically, this is just a filesystem which is not backed by a
single block device. Normally this block device's dev_t is stored in
the super block. For anonymous super blocks a unique reserved dev_t
is assigned as part of get_sb().
This sb->s_dev must then be set in the returned stat structures as
stat->st_dev. This allows userspace utilities to easily detect the
boundries of a specific filesystem. Tools such as 'du' depend on this
for proper accounting.
Additionally, under OpenSolaris the statfs->f_fsid is set to the device
id. To preserve consistency with OpenSolaris we also set the fsid to
the device id. Other Linux filesystem (ext) set the fsid to a unique
value determined by the filesystems uuid. This value is unique but
maintains no relationship to the device id. This may be desirable
when exporting NFS filesystem because it minimizes to chance of a
client observing the same fsid from two different servers.
Detect early on in configure if the Modules.symvers file is missing.
Without this file there will be build failures later and it's best
to catch this early and provide a useful error. In this case the
most likely problem is the kernel-devel packages are not installed.
It may also be possible that they are using an unbuilt custom kernel
in which case they must build the kernel first.
Until support is added for preemptible kernels detect this at
configure time and make it fatal. Otherwise, it is possible to
have a successful build and kernel modules with flakey behavior.
The libspl and libzpool libraries were missing from the libzfs
Makefile.am. They should be explicitly listed to avoid build
issues when compiling static libraries and binaries.
Additionally, ensure libzpool is built before libzfs because
libzfs is dependent on libzpool. This was also exposed as an
issue when forcing static linking.
The AT_ versions of these macros are used on Solaris and while they
map to their Linux equivilants the code has been updated to use the
ATTR_ versions.
Move 'tmpxvattr' from the stack to the heap to minimize stack
space usage. This is enough to get us below the 1024 byte stack
frame warning. That however is still a large stack frame and it
should be further reduced by moving the 'bulk' and 'xattr_bulk'
sa_bulk_attr_t variables to the heap in a future patch.
When I began work on the Posix layer it immediately became clear to
me that to integrate cleanly with the Linux VFS certain Solaris
specific things would have to go. One of these things was to elimate
as many Solaris specific types from the ZPL layer as possible. They
would be replaced with their Linux equivalents. This would not only
be good for performance, but for the general readability and health of
the code. The Solaris and Linux VFS are different beasts and should
be treated as such. Most of the code remains common for constructing
transactions and such, but there are subtle and important differenced
which need to be repsected.
This policy went quite for for certain types such as the vnode_t,
and it initially seemed to be working out well for the vattr_t. There
was a relatively small amount of related xvattr_t code I was forced to
comment out with HAVE_XVATTR. But it didn't look that hard to come
back soon and replace it all with a native Linux type.
However, after going doing this path with xvattr some distance it
clear that this code was woven in the ZPL more deeply than I thought.
In particular its hooks went very deep in to the ZPL replay code
and replacing it would not be as easy as I originally thought.
Rather than continue persuing replacing and removing this code I've
taken a step back and reevaluted things. This commit reverts many of
my previous commits which removed xvattr related code. It restores
much of the code to its original upstream state and now relies on
improved xvattr_t support in the zfs package itself.
The result of this is that much of the code which I had commented
out, which accidentally broke things like replay, is now back in
place and working. However, there may be a small performance
impact for getattr/setattr operations because they now require
a translation from native Linux to Solaris types. For now that's
a price I'm willing to pay. Once everything is completely functional
we can revisting the issue of removing the vattr_t/xvattr_t types.
With the removal of the minimal xvattr support from the spl this
support needs to be replaced in the zfs package. This is fairly
easily accomplished by directly adding portions of the sys/vnode.h
header from OpenSolaris. These xvattr additions have been placed
in the sys/xvattr.h header file and included as needed where simply
a sys/vnode.h was included before.
In additon to the xvattr types and helper macros two functions
were also included. The xva_init() and xva_getxoptattr() functions
were included as static inline functions in xvattr.h. They are
simple enough and it was simpler to place them here rather than
in their own .c file.
Darik Horn [Mon, 28 Feb 2011 16:15:05 +0000 (10:15 -0600)]
Add the zpool and filesystem versions
Print the supported zpool and filesystem versions at module load
time. This change removes an ambiguity and adds information that
system administrators care about. The phrase "ZFS pool version %s"
is the same as zpool upgrade -v so that the operator is familiar
with the message.
ZFS: Loaded module v0.6.0, ZFS pool version 28, ZFS filesystem version 5
ZFS: Unloaded module v0.6.0
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
projects / zfs / log