Ned Bass [Fri, 15 Apr 2016 18:55:03 +0000 (18:55 +0000)]
Fix ZPL miswrite of default POSIX ACL
Commit 4967a3e introduced a typo that caused the ZPL to store the
intended default ACL as an access ACL. Due to caching this problem
may not become visible until the filesystem is remounted or the inode
is evicted from the cache. Fix the typo and add a regression test.
Signed-off-by: Ned Bass <bass6@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Closes #4520
Colin Ian King [Thu, 14 Apr 2016 07:58:09 +0000 (08:58 +0100)]
Fix inverted logic on none elevator comparison
Commit d1d7e2689db9e03f1 ("cstyle: Resolve C style issues") inverted
the logic on the none elevator comparison. Fix this and make it
cstyle warning clean.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4507
In replacement test, it spawns a process to truncate a file background
and make sure that the process exists 1 second later. However, the
process may have finished its work and exited therefore it has the
chance to report a false alarm.
This patch just removed those sanity check.
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4516
When ZFS is installed by 'make install', programs will be installed
into '/usr/local'. ZFS test scripts can't locate programs 'zpool'
that caused tests failure.
Fix typo in help message.
Add sanity check to for ksh and generate a useful error message.
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4495
Add atime_003_pos to test relatime=on, we do check_atime_updated twice, the
first time should success and the second time should fail. We also modify
atime_001_pos to do check_atime_updated twice and both times should succeed.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4482
Chunwei Chen [Thu, 31 Mar 2016 23:52:03 +0000 (16:52 -0700)]
Enable lazytime semantic for atime
Linux 4.0 introduces lazytime. The idea is that when we update the atime, we
delay writing it to disk for as long as it is reasonably possible.
When lazytime is enabled, dirty_inode will be called with only I_DIRTY_TIME
flag whenever i_atime is updated. So under such condition, we will set
z_atime_dirty. We will only write it to disk if file is closed, inode is
evicted or setattr is called. Ideally, we should also write it whenever SA
is going to be updated, but it is left for future improvement.
There's one thing that we should take care of now that we allow i_atime to be
dirty. In original implementation, whenever SA is modified, zfs_inode_update
will be called to overwrite every thing in inode. This will cause dirty
i_atime to be discarded. We fix this by don't overwrite i_atime in
zfs_inode_update. We only overwrite i_atime when allocating new inode or doing
zfs_rezget with zfs_inode_update_new.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4482
Chunwei Chen [Wed, 30 Mar 2016 00:53:34 +0000 (17:53 -0700)]
Fix atime handling and relatime
The problem for atime:
We have 3 places for atime: inode->i_atime, znode->z_atime and SA. And its
handling is a mess. A huge part of mess regarding atime comes from
zfs_tstamp_update_setup, zfs_inode_update, and zfs_getattr, which behave
inconsistently with those three values.
zfs_tstamp_update_setup clears z_atime_dirty unconditionally as long as you
don't pass ATTR_ATIME. Which means every write(2) operation which only updates
ctime and mtime will cause atime changes to not be written to disk.
Also zfs_inode_update from write(2) will replace inode->i_atime with what's
inside SA(stale). But doesn't touch z_atime. So after read(2) and write(2).
You'll have i_atime(stale), z_atime(new), SA(stale) and z_atime_dirty=0.
Now, if you do stat(2), zfs_getattr will actually replace i_atime with what's
inside, z_atime. So you will have now you'll have i_atime(new), z_atime(new),
SA(stale) and z_atime_dirty=0. These will all gone after umount. And you'll
leave with a stale atime.
The problem for relatime:
We do have a relatime config inside ZFS dataset, but how it should interact
with the mount flag MS_RELATIME is not well defined. It seems it wanted
relatime mount option to override the dataset config by showing it as
temporary in `zfs get`. But at the same time, `zfs set relatime=on|off` would
also seems to want to override the mount option. Not to mention that
MS_RELATIME flag is actually never passed into ZFS, so it never really worked.
How Linux handles atime:
The Linux kernel actually handles atime completely in VFS, except for writing
it to disk. So if we remove the atime handling in ZFS, things would just work,
no matter it's strictatime, relatime, noatime, or even O_NOATIME. And whenever
VFS updates the i_atime, it will notify the underlying filesystem via
sb->dirty_inode().
And also there's one thing to note about atime flags like MS_RELATIME and
other flags like MS_NODEV, etc. They are mount point flags rather than
filesystem(sb) flags. Since native linux filesystem can be mounted at multiple
places at the same time, they can all have different atime settings. So these
flags are never passed down to filesystem drivers.
What this patch tries to do:
We remove znode->z_atime, since we won't gain anything from it. We remove most
of the atime handling and leave it to VFS. The only thing we do with atime is
to write it when dirty_inode() or setattr() is called. We also add
file_accessed() in zpl_read() since it's not provided in vfs_read().
After this patch, only the MS_RELATIME flag will have effect. The setting in
dataset won't do anything. We will make zfstuil to mount ZFS with MS_RELATIME
set according to the setting in dataset in future patch.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4482
As described in torvalds/linux@4a2d057e the macros
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were originally introduced
to make it possible to add bigger chunks to the page cache. This
never panned out and it has therefore been removed from the kernel.
ZFS has been updated to use the PAGE_{SIZE,SHIFT,MASK,ALIGN} macros
and calls to page_cache_release() have been replaced with put_page().
There was no need to introduce a configure check for this because
these interfaces have existed for a very long time.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Closes #4489
Accidentally introduced by commit e4023e4. The AM_CONDITIONAL
cannot be located where it can be invoked conditionally, as in
the `--with-config=user` case. Relocate it to the top level
ZFS_AC_CONFIG macro along with the other AM_CONDITIONALs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4416
Colin Ian King [Wed, 30 Mar 2016 22:00:23 +0000 (23:00 +0100)]
Add support 32 bit FS_IOC32_{GET|SET}FLAGS compat ioctls
We need 32 bit userspace FS_IOC32_GETFLAGS and FS_IOC32_SETFLAGS
compat ioctls for systems such as powerpc64. We use the normal
compat ioctl idiom as used by a variety of file systems to provide
this support.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4477
Brian Behlendorf [Thu, 31 Mar 2016 21:50:16 +0000 (14:50 -0700)]
Only build devname2devid when libudev headers are available
Accidentally introduced by commit 39fc0cb. The devname2devid utility
which depends on libudev must only be built when libudev headers are
available. This is accomplished through an AM_CONDITIONAL.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4416
Don Brady [Mon, 14 Mar 2016 16:04:21 +0000 (10:04 -0600)]
Add support for devid and phys_path keys in vdev disk labels
This is foundational work for ZED.
Updates a leaf vdev's persistent device strings on Linux platform
* only applies for a dedicated leaf vdev (aka whole disk)
* updated during pool create|add|attach|import
* used for matching device matching during auto-{online,expand,replace}
* stored in a leaf disk config label (i.e. alongside 'path' NVP)
* can opt-out using env var ZFS_VDEV_DEVID_OPT_OUT=YES
Andriy Gapon [Fri, 25 Mar 2016 14:29:35 +0000 (16:29 +0200)]
Expand EDQUOT variable
Results in failures with ksh version 93v- 2014-06-25. This appears
to not be an issue with ksh version 93u+ 2012-08-01. The expanded
versions works correctly for both.
Signed-off-by: Andriy Gapon <andriy.gapon@clusterhq.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4452
The `zfs userspace` squashes all entries with unresolved numeric
values into a single output entry due to the comparsion always
made by the string name which is empty in case of unresolved IDs.
Fix this by falling to a numerical comparison when either one
of string values is not found. This then compares any numerical
values after all with a name resolved.
Signed-off-by: Pavel Boldin <boldin.pavel@gmail.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4440
Effectively provide our own version of assert()/verify() for use
in user space. This minimizes our dependencies and aligns the
user space assertion handling with what's used in the kernel.
Signed-off-by: Carlo Landmeter <clandmeter@gmail.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4449
DHE [Sun, 27 Mar 2016 19:58:27 +0000 (15:58 -0400)]
gcc build error: -Wbool-compare in metaslab.c
When debugging is enabled on a very recent version of gcc
(tested with 5.3.0), DVA_SET_GANG(dva, !!(flags)) fails
because an assertion causes a comparison between what is
technically a boolean and an integer.
Signed-off-by: DHE <git@dehacked.net> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4465
Brian Behlendorf [Sat, 26 Mar 2016 21:17:26 +0000 (14:17 -0700)]
Fix zpool_scrub_* test cases
The zpool_scrub_002, zpool_scrub_003, zpool_scrub_004 test cases fail
reliably when running against small pools or fast storage. This
occurs because the scrub/resilver operation completes before subsequent
commands can be run.
A one second delay has been added to 10% of zio's in order to ensure
the scrub/resilver operation will run for at least several seconds.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4450
Brian Behlendorf [Fri, 25 Mar 2016 19:40:58 +0000 (12:40 -0700)]
zloop.sh requires bash
The zloop.sh script requires bash. It will require further improvements
to be compatible with the alternatives such as dash. This resolves the
ztest failures observed under Ubuntu in the automated tested.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4441
Brian Behlendorf [Wed, 23 Mar 2016 01:08:59 +0000 (18:08 -0700)]
Add zloop.sh test script
Add Chris Williamson's "new" zloop script so that it may be
intergated with ZoLs automated testing. The original script may
be found in the openzfs-build repository on Github.
Minor modifications were made to the script so it can be run
directly from the ZoL source tree or from installed packages.
Additionally it was updated to use gdb instead of mdb to
extact debugging information from a core dump.
Brian Behlendorf [Thu, 17 Mar 2016 22:32:33 +0000 (15:32 -0700)]
Fix zdb -e and zhack thread_init()
This issue was caused by calling `thread_init()` and `thread_fini()`
multiple times resulting in `kthread_key` being invalid. To resolve
the issue the explicit calls to `thread_init()` and `thread_fini()`
required by the `zpool` command have been moved in to the command.
Consumers such as `zdb` and `zhack` perform the same initialized
through `kernel_init()` and `kernel_fini()`.
Resolving this issue allows multiple additional test cases to
be enabled.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Signed-off-by: Chunwei Chen <tuxoko@gmail.com> Signed-off-by: Tim Chase <tim@chase2k.com>
Closes #4331
Gvozden Neskovic [Mon, 29 Feb 2016 18:42:27 +0000 (19:42 +0100)]
Support for vectorized algorithms on x86
This is initial support for x86 vectorized implementations of ZFS parity
and checksum algorithms.
For the compilation phase, configure step checks if toolchain supports relevant
instruction sets. Each implementation must ensure that the code is not passed
to compiler if relevant instruction set is not supported. For this purpose,
following new defines are provided if instruction set is supported:
- HAVE_SSE,
- HAVE_SSE2,
- HAVE_SSE3,
- HAVE_SSSE3,
- HAVE_SSE4_1,
- HAVE_SSE4_2,
- HAVE_AVX,
- HAVE_AVX2.
For detecting if an instruction set can be used in runtime, following functions
are provided in (include/linux/simd_x86.h):
- zfs_sse_available()
- zfs_sse2_available()
- zfs_sse3_available()
- zfs_ssse3_available()
- zfs_sse4_1_available()
- zfs_sse4_2_available()
- zfs_avx_available()
- zfs_avx2_available()
- zfs_bmi1_available()
- zfs_bmi2_available()
These function should be called once, on module load, or initialization.
They are safe to use from user and kernel space.
If an implementation is using more than single instruction set, both compiler
and runtime support for all relevant instruction sets should be checked.
Kernel fpu methods:
- kfpu_begin()
- kfpu_end()
Use __get_cpuid_max and __cpuid_count from <cpuid.h>
Both gcc and clang have support for these. They also handle ebx register
in case it is used for PIC code.
Richard Yao [Tue, 15 Mar 2016 17:28:07 +0000 (13:28 -0400)]
Cleanup linking
I noticed during code review of zfsonlinux/zfs#4385 that the author of a
commit had peppered the various Makefile.am files with `$(TIRPC_LIBS)`
when putting it into `lib/libspl/Makefile.am` should have sufficed. Upon
further examination, it seems that he had copied what we do with
`$(ZLIB)`. We also have a bit of that with `-ldl` too. Unfortunately,
what we do is wrong, so lets fix it to set a good example for future
contributors.
In addition, we have multiple `-lz` and `-luuid` passed to the compiler
because each `AC_CHECK_LIB` adds it to `$LIBS`. That is somewhat
annoying to see, so we switch to `AC_SEARCH_LIBS` to avoid it. This is
consistent with the recommendation to use `AC_SEARCH_LIBS` over
`AC_CHECK_LIB` by autotools upstream:
In an ideal world, this would translate into improvements in ELF's
`DT_NEEDED` entries, but that is not the case because of a couple of
bugs in libtool.
The first bug causes libtool to overlink by using static link
dependencies for dynamic linking:
The workaround for this should be to pass `-Wl,--as-needed` in
`LDFLAGS`. That leads us to the second bug, where libtool passes
`LDFLAGS` after the libraries are specified and `ld` will only honor
`--as-needed` on libraries specified before it:
There are a few possible workarounds for the second bug. One is to
either patch the compiler spec file to specify `-Wl,--as-needed` or pass
`-Wl,--as-needed` via `CC` like `CC='gcc -Wl,--as-needed'` so that it is
specified early. Another is to patch ltmain.sh like Gentoo does:
Without one of those workarounds, this cleanup provides no benefit in
terms of `DT_NEEDED` entry generation. It should still be an improvement
because it nicely simplifies the code while encouraging good habits when
patching autotools scripts.
Signed-off-by: Richard Yao <ryao@gentoo.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4426
Signed-off-by: Dimitri John Ledkov <xnox@ubuntu.com> Signed-off-by: Richard Yao <ryao@gentoo.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4425
Add the ZFS Test Suite and test-runner framework from illumos.
This is a continuation of the work done by Turbo Fredriksson to
port the ZFS Test Suite to Linux. While this work was originally
conceived as a stand alone project integrating it directly with
the ZoL source tree has several advantages:
* Allows the ZFS Test Suite to be packaged in zfs-test package.
* Facilitates easy integration with the CI testing.
* Users can locally run the ZFS Test Suite to validate ZFS.
This testing should ONLY be done on a dedicated test system
because the ZFS Test Suite in its current form is destructive.
* Allows the ZFS Test Suite to be run directly in the ZoL source
tree enabled developers to iterate quickly during development.
* Developers can easily add/modify tests in the framework as
features are added or functionality is changed. The tests
will then always be in sync with the implementation.
Full documentation for how to run the ZFS Test Suite is available
in the tests/README.md file.
Warning: This test suite is designed to be run on a dedicated test
system. It will make modifications to the system including, but
not limited to, the following.
* Adding new users
* Adding new groups
* Modifying the following /proc files:
* /proc/sys/kernel/core_pattern
* /proc/sys/kernel/core_uses_pid
* Creating directories under /
Notes:
* Not all of the test cases are expected to pass and by default
these test cases are disabled. The failures are primarily due
to assumption made for illumos which are invalid under Linux.
* When updating these test cases it should be done in as generic
a way as possible so the patch can be submitted back upstream.
Most existing library functions have been updated to be Linux
aware, and the following functions and variables have been added.
* Functions:
* is_linux - Used to wrap a Linux specific section.
* block_device_wait - Waits for block devices to be added to /dev/.
* Variables: Linux Illumos
* ZVOL_DEVDIR "/dev/zvol" "/dev/zvol/dsk"
* ZVOL_RDEVDIR "/dev/zvol" "/dev/zvol/rdsk"
* DEV_DSKDIR "/dev" "/dev/dsk"
* DEV_RDSKDIR "/dev" "/dev/rdsk"
* NEWFS_DEFAULT_FS "ext2" "ufs"
* Many of the disabled test cases fail because 'zfs/zpool destroy'
returns EBUSY. This is largely causes by the asynchronous nature
of device handling on Linux and is expected, the impacted test
cases will need to be updated to handle this.
* There are several test cases which have been disabled because
they can trigger a deadlock. A primary example of this is to
recursively create zpools within zpools. These tests have been
disabled until the root issue can be addressed.
* Illumos specific utilities such as (mkfile) should be added to
the tests/zfs-tests/cmd/ directory. Custom programs required by
the test scripts can also be added here.
* SELinux should be either is permissive mode or disabled when
running the tests. The test cases should be updated to conform
to a standard policy.
* Redundant test functionality has been removed (zfault.sh).
* Existing test scripts (zconfig.sh) should be migrated to use
the framework for consistency and ease of testing.
* The DISKS environment variable currently only supports loopback
devices because of how the ZFS Test Suite expects partitions to
be named (p1, p2, etc). Support must be added to generate the
correct partition name based on the device location and name.
* The ZFS Test Suite is part of the illumos code base at:
https://github.com/illumos/illumos-gate/tree/master/usr/src/test
Original-patch-by: Turbo Fredriksson <turbo@bayour.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes #6
Closes #1534
Alex Wilson [Fri, 11 Mar 2016 23:25:32 +0000 (00:25 +0100)]
Illumos 6681 - zfs list burning lots of time in dodefault() via dsl_prop_*
6681 zfs list burning lots of time in dodefault() via dsl_prop_*
Reviewed by: Patrick Mooney <patrick.mooney@joyent.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Matthew Ahrens <mahrens@delphix.com>
Gordan Bobic [Tue, 15 Mar 2016 17:17:51 +0000 (17:17 +0000)]
Fix aarch64 compilation
sys/param.h depends on types defined in sys/types.h
(hrtime_t & timestruc_t).
Signed-off-by: Gordan Bobic <gordan@redsleeve.org> Signed-off-by: Christopher J. Morrone <morrone2@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4420
Paul Dagnelie [Fri, 26 Feb 2016 01:45:19 +0000 (20:45 -0500)]
Illumos 6370 - ZFS send fails to transmit some holes
6370 ZFS send fails to transmit some holes
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Stefan Ring <stefanrin@gmail.com>
Reviewed by: Steven Burgess <sburgess@datto.com>
Reviewed by: Arne Jansen <sensille@gmx.net>
Approved by: Robert Mustacchi <rm@joyent.com>
In certain circumstances, "zfs send -i" (incremental send) can produce
a stream which will result in incorrect sparse file contents on the
target.
The problem manifests as regions of the received file that should be
sparse (and read a zero-filled) actually contain data from a file that
was deleted (and which happened to share this file's object ID).
Note: this can happen only with filesystems (not zvols, because they do
not free (and thus can not reuse) object IDs).
Note: This can happen only if, since the incremental source (FromSnap),
a file was deleted and then another file was created, and the new file
is sparse (i.e. has areas that were never written to and should be
implicitly zero-filled).
We suspect that this was introduced by 4370 (applies only if hole_birth
feature is enabled), and made worse by 5243 (applies if hole_birth
feature is disabled, and we never send any holes).
The bug is caused by the hole birth feature. When an object is deleted
and replaced, all the holes in the object have birth time zero. However,
zfs send cannot tell that the holes are new since the file was replaced,
so it doesn't send them in an incremental. As a result, you can end up
with invalid data when you receive incremental send streams. As a
short-term fix, we can always send holes with birth time 0 (unless it's
a zvol or a dataset where we can guarantee that no objects have been
reused).
Ported-by: Steven Burgess <sburgess@datto.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4369
Closes #4050
Brian Behlendorf [Thu, 17 Jul 2014 17:46:46 +0000 (10:46 -0700)]
Relax MBR partition scanning requirement
When checking a whole disk to see if it can be safely added to
the pool a variety of checks are done. One of those checks is
to attempt to determine the partition information and scan all
the partitions for existing filesystems.
Since ZoL contains a EFI library this partition scanning is
easy to do for GPT partitioned disks. However, for non-GPT
partitioned disks (MBR/EBR) things are a bit harder. The lack of
a convenient library means non-GPT partitioned disks will not
have all their partitions checked. For this reason, the default
behavior was to require the force option. For example:
invalid vdev specification
use '-f' to override the following errors:
/dev/vdb does not contain an GPT label but it may contain partition
information in the MBR.
However in practice requiring the force option for this case is
counter-intuitively less safe. The reason is because only the first
error is returned. By passing the force option it will suppress
this first warning and potentially others you were not aware of.
Therefore this patch inverts the default behavior for non-GPT
formated disks (unformatted, MBR/EBR, etc). If no GPT table is
detected and there is no file system detected on the provided
block device. Then it will be assumed that block device is safe
to use.
Longer term it would be nice to see MBR/EBR scanning added to
the utilities. This should be fairly straight forward to do.
However these days it's somewhat less critical because Linux
defaults to GPT partition tables for devices 2TB or larger.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #2660
Closes #2274
Boris Protopopov [Wed, 23 Sep 2015 16:34:51 +0000 (12:34 -0400)]
Fix lock order inversion with zvol_open()
zfsonlinux issue #3681 - lock order inversion between zvol_open() and
dsl_pool_sync()...zvol_rename_minors()
Remove trylock of spa_namespace_lock as it is no longer needed when
zvol minor operations are performed in a separate context with no
prior locking state; the spa_namespace_lock is no longer held
when bdev->bd_mutex or zfs_state_lock might be taken in the code
paths originating from the zvol minor operation callbacks.
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #3681
Boris Protopopov [Sat, 22 Mar 2014 09:07:14 +0000 (05:07 -0400)]
Add support for asynchronous zvol minor operations
zfsonlinux issue #2217 - zvol minor operations: check snapdev
property before traversing snapshots of a dataset
zfsonlinux issue #3681 - lock order inversion between zvol_open()
and dsl_pool_sync()...zvol_rename_minors()
Create a per-pool zvol taskq for asynchronous zvol tasks.
There are a few key design decisions to be aware of.
* Each taskq must be single threaded to ensure tasks are always
processed in the order in which they were dispatched.
* There is a taskq per-pool in order to keep the pools independent.
This way if one pool is suspended it will not impact another.
* The preferred location to dispatch a zvol minor task is a sync
task. In this context there is easy access to the spa_t and
minimal error handling is required because the sync task must
succeed.
Support for asynchronous zvol minor operations address issue #3681.
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #2217
Closes #3678
Closes #3681
Brian Behlendorf [Thu, 10 Mar 2016 17:14:27 +0000 (09:14 -0800)]
Remove RPM package restriction
ZFS on Linux is regularly tested on arm, ppc, ppc64, i686 and x86_64
architectures. Given this the artificial architecture restriction in
the packaging has been removed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf [Fri, 19 Feb 2016 23:43:43 +0000 (15:43 -0800)]
Require libblkid
Historically libblkid support was detected as part of configure
and optionally enabled. This was done because at the time support
for detecting ZFS pool vdevs had just be added to libblkid and
those updated packages were not yet part of many distributions.
This is no longer the case and any reasonably current distribution
will ship a version of libblkid which can detect ZFS pool vdevs.
This patch makes libblkid mandatory at build time and libblkid
the preferred method of scanning for ZFS pools. For distributions
which include a modern version of libblkid there is no change in
behavior. Explicitly scanning the default search paths is still
supported and can be enabled with the '-s' command line option.
Additionally making libblkid mandatory means that the 'zpool create'
command can reliably detect if a specified device has an existing
non-ZFS filesystem (ext4, xfs) and print a warning.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #2448
Chris Dunlap [Tue, 1 Mar 2016 20:23:55 +0000 (12:23 -0800)]
Ensure zed _finish_daemonize() leaves fds 0-2 open
In zed's _finish_daemonize(), /dev/null is open()d onto a temporary
file descriptor which is then dup()d onto stdin, stdout, and stderr.
But if file descriptors 0, 1, or 2 are not already open at the start
of this function, then the temporary file descriptor will fall within
this range and be inadvertently closed when the function cleans up.
This commit adds a check to prevent inadvertently closing this
(presumably temporary) file descriptor when it shouldn't.
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4384
Tony Hutter [Wed, 2 Mar 2016 20:57:06 +0000 (12:57 -0800)]
Fix zpool iostat bandwidth/ops calculation
print_vdev_stats() subtracts the old bandwidth/ops stats from the new stats
to calculate the bandwidth/ops numbers in "zpool iostat". However when the
TXG numbers change between stats, zpool_refresh_stats() will incorrectly assign
a NULL to the old stats. This causes print_vdev_stats() to use zeroes for
the old bandwidth/ops numbers, resulting in an inaccurate calculation.
This fix allows the calculation to happen even when TXGs change.
Signed-off-by: Tony Hutter <hutter2@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4387
Carlo Landmeter [Tue, 1 Mar 2016 15:36:28 +0000 (16:36 +0100)]
Add support for alpine linux
Both Alpine Linux and Gentoo use OpenRC so we share its logic
Signed-off-by: Carlo Landmeter <clandmeter@gmail.com> Signed-off-by: Richard Yao <ryao@gentoo.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4386
ab-oe [Fri, 26 Feb 2016 07:33:44 +0000 (08:33 +0100)]
Make zvol update volsize operation synchronous.
There is a race condition when new transaction group is added
to dp->dp_dirty_datasets list by the zap_update in the zvol_update_volsize.
Meanwhile, before these dirty data are synchronized, the receive process
can cause that dmu_recv_end_sync is executed. Then finally dirty data
are going to be synchronized but the synchronization ends with the NULL
pointer dereference error.
Signed-off-by: ab-oe <arkadiusz.bubala@open-e.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4116
smh [Sat, 13 Feb 2016 01:47:22 +0000 (20:47 -0500)]
FreeBSD r256956: Improve ZFS N-way mirror read performance by using load and locality information.
The existing algorithm selects a preferred leaf vdev based on offset of the zio
request modulo the number of members in the mirror. It assumes the devices are
of equal performance and that spreading the requests randomly over both drives
will be sufficient to saturate them. In practice this results in the leaf vdevs
being under utilized.
The new algorithm takes into the following additional factors:
* Load of the vdevs (number outstanding I/O requests)
* The locality of last queued I/O vs the new I/O request.
Within the locality calculation additional knowledge about the underlying vdev
is considered such as; is the device backing the vdev a rotating media device.
This results in performance increases across the board as well as significant
increases for predominantly streaming loads and for configurations which don't
have evenly performing devices.
The following are results from a setup with 3 Way Mirror with 2 x HD's and
1 x SSD from a basic test running multiple parrallel dd's.
With pre-fetch disabled (vfs.zfs.prefetch_disable=1):
== Stripe Balanced (default) ==
Read 15360MB using bs: 1048576, readers: 3, took 161 seconds @ 95 MB/s
== Load Balanced (zfslinux) ==
Read 15360MB using bs: 1048576, readers: 3, took 297 seconds @ 51 MB/s
== Load Balanced (locality freebsd) ==
Read 15360MB using bs: 1048576, readers: 3, took 54 seconds @ 284 MB/s
With pre-fetch enabled (vfs.zfs.prefetch_disable=0):
== Stripe Balanced (default) ==
Read 15360MB using bs: 1048576, readers: 3, took 91 seconds @ 168 MB/s
== Load Balanced (zfslinux) ==
Read 15360MB using bs: 1048576, readers: 3, took 108 seconds @ 142 MB/s
== Load Balanced (locality freebsd) ==
Read 15360MB using bs: 1048576, readers: 3, took 48 seconds @ 320 MB/s
In addition to the performance changes the code was also restructured, with
the help of Justin Gibbs, to provide a more logical flow which also ensures
vdevs loads are only calculated from the set of valid candidates.
The following additional sysctls where added to allow the administrator
to tune the behaviour of the load algorithm:
* vfs.zfs.vdev.mirror.rotating_inc
* vfs.zfs.vdev.mirror.rotating_seek_inc
* vfs.zfs.vdev.mirror.rotating_seek_offset
* vfs.zfs.vdev.mirror.non_rotating_inc
* vfs.zfs.vdev.mirror.non_rotating_seek_inc
These changes where based on work started by the zfsonlinux developers:
https://github.com/zfsonlinux/zfs/pull/1487
Porting notes:
- The tunables were adjusted to have ZoL-style names.
- The code was modified to use ZoL's vd_nonrot.
- Fixes were done to make cstyle.pl happy
- Merge conflicts were handled manually
- freebsd/freebsd@e186f564bc946f82c76e0b34c2f0370ed9aea022 by my
collegue Andriy Gapon has been included. It applied perfectly, but
added a cstyle regression.
- This replaces 556011dbec2d10579819078559a77630fc559112 entirely.
- A typo "IO'a" has been corrected to say "IO's"
- Descriptions of new tunables were added to man/man5/zfs-module-parameters.5.
Ported-by: Richard Yao <ryao@gentoo.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4334
Brian Behlendorf [Fri, 26 Feb 2016 16:57:30 +0000 (08:57 -0800)]
Change full path subcommand flag from -p to -P
Commit d2f3e29 introduced the -p option which outputs full paths
for vdevs to multiple zpool subcommands. When this was merged
there was no conflict for this flag letter. However it's certain
there will be a conflict with the -p (parsable) flag used by other
subcommands. Therefore, -p is being changed to -P to avoid this.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4368
Richard Yao [Sun, 29 Dec 2013 18:40:46 +0000 (13:40 -0500)]
Add -gLp to zpool subcommands for alt vdev names
The following options have been added to the zpool add, iostat,
list, status, and split subcommands. The default behavior was
not modified, from zfs(8).
-g Display vdev GUIDs instead of the normal short
device names. These GUIDs can be used in-place of
device names for the zpool detach/off‐
line/remove/replace commands.
-L Display real paths for vdevs resolving all symbolic
links. This can be used to lookup the current block
device name regardless of the /dev/disk/ path used
to open it.
-p Display full paths for vdevs instead of only the
last component of the path. This can be used in
conjunction with the -L flag.
This behavior may also be enabled using the following environment
variables.
This change is based on worked originally started by Richard Yao
to add a -g option. Then extended by @ilovezfs to add a -L option
for openzfsonosx. Those changes have been merged, re-factored,
a -p option added and extended to all relevant zpool subcommands.
Original-patch-by: Richard Yao <ryao@gentoo.org> Extended-by: ilovezfs <ilovezfs@icloud.com> Extended-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: ilovezfs <ilovezfs@icloud.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #2011
Closes #4341
Grischa Zengel [Fri, 19 Feb 2016 18:20:55 +0000 (19:20 +0100)]
Add nfs-kernel-server for Debian
Debian based systems use nfs-kernel-server as the service name.
List both nfs-server.service and nfs-kernel-server.service so
this service will work on multiple distributions.
Signed-off-by: Grischa Zengel <github.zfsonlinux@zengel.info> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4350
Brian Behlendorf [Wed, 10 Feb 2016 18:42:01 +0000 (10:42 -0800)]
Add l2arc_max_block_size tunable
Set a limit for the largest compressed block which can be written
to an L2ARC device. By default this limit is set to 16M so there
is no change in behavior.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Richard Elling <Richard.Elling@RichardElling.com> Signed-off-by: Tim Chase <tim@chase2k.com>
Closes #4323
Boris Protopopov [Tue, 16 Feb 2016 19:52:55 +0000 (14:52 -0500)]
Make zvol minor functionality more robust
Close the race window in zvol_open() to prevent removal of
zvol_state in the 'first open' code path. Move the call to
check_disk_change() under zvol_state_lock to make sure the
zvol_media_changed() and zvol_revalidate_disk() called by
check_disk_change() are invoked with positive zv_open_count.
Skip opened zvols when removing minors and set private_data
to NULL for zvols that are not in use whose minors are being
removed, to indicate to zvol_open() that the state is gone.
Skip opened zvols when renaming minors to avoid modifying
zv_name that might be in use, e.g. in zvol_ioctl().
Drop zvol_state_lock before calling add_disk() when creating
minors to avoid deadlocks with zvol_open().
Wrap dmu_objset_find() with spl_fstran_mark()/unmark().
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes #4344
Richard Yao [Sat, 6 Feb 2016 04:10:13 +0000 (23:10 -0500)]
Call dmu_read_uio_dbuf() in zvol_read()
The difference between `dmu_read_uio()` and `dmu_read_uio_dbuf()` is
that the former takes a hold while the latter uses an existing hold.
`zfs_read()` in the ZPL will use `dmu_read_uio_dbuf()` while
our analogous `zvol_write()` will use `dmu_write_uio_dbuf()`, but for no
apparent reason, we inherited a `zvol_read()` function from
OpenSolaris that does `dmu_read_uio()`. illumos-gate also still
uses `dmu_read_uio()` to this day. Lets switch to `dmu_read_uio_dbuf()`,
which is more performant.
Signed-off-by: Richard Yao <ryao@gentoo.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Tim Chase <tim@chase2k.com> Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Closes #4316
Richard Yao [Sat, 6 Feb 2016 01:36:07 +0000 (20:36 -0500)]
Clean up zvol request processing to pass uio and fix porting regressions
In illumos-gate, `zvol_read` and `zvol_write` are both passed uio_t
rather than bio_t. Since we are translating from bio to uio for both, we
might as well unify the logic and have code more similar to its illumos
counterpart. At the same time, we can fix some regressions that occurred
versus the original code from illumos-gate.
We refactor zvol_write to take uio and also correct the
following problems:
1. We did `dnode_hold()` on each IO when we already had a hold.
2. We would attempt to send writes that exceeded `DMU_MAX_ACCESS` to the
DMU.
3. We could call `zil_commit()` twice. In this case, this is because
Linux uses the `->write` function to send flushes and can aggregate the
flush with a write. If a synchronous write occurred with the flush, we
effectively flushed twice when there is no need to do that.
zvol_read also suffers from the first two problems. Other platforms
suffer from the first, so we leave that for a second patch so that there
is a discrete patch for them to cherry-pick.
Signed-off-by: Richard Yao <ryao@gentoo.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Tim Chase <tim@chase2k.com> Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Closes #4316
Olaf Faaland [Wed, 20 Jan 2016 22:01:28 +0000 (14:01 -0800)]
Make configure error clearer when failing to find SPL
Signed-off-by: Olaf Faaland <faaland1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes #4251
Chunwei Chen [Fri, 22 Jan 2016 20:23:55 +0000 (12:23 -0800)]
Remove wrong ASSERT in annotate_ecksum
When using large blocks like 1M, there will be more than UINT16_MAX qwords in
one block, so this ASSERT would go off. Also, it is possible for the histogram
to overflow. We cap them to UINT16_MAX to prevent this.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4257
Prevent zpool_find_vdev() from truncating vdev path
When extracting tokens from the string strtok(2) is allowed to modify
the passed buffer. Therefore the zfs_strcmp_pathname() function must
make a copy of the passed string before passing it to strtok(3).
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Don Brady <don.brady@intel.com>
Closes #4312
Paul Dagnelie [Fri, 5 Feb 2016 21:47:48 +0000 (13:47 -0800)]
Illumos 5809 - Blowaway full receive in v1 pool causes kernel panic
5809 Blowaway full receive in v1 pool causes kernel panic
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Reviewed by: Will Andrews <will@freebsd.org>
Approved by: Gordon Ross <gwr@nexenta.com>
Illumos 5767 - fix several problems with zfs test suite
5767 fix several problems with zfs test suite
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Porting Notes:
- Only the updates to zpool_main.c were kept because the ZFS test
suite is not currently part of the ZoL source tree. The test
suite itself should be updated to include the latest versions
of the tests once we're running it for every commit
- Fixes `zpool list` output.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Tim Chase [Wed, 3 Feb 2016 16:07:34 +0000 (10:07 -0600)]
Correctly parse -R flag arguments
Currently, only the 'b' flag takes an argument which is an offset into
the block at which a blkptr should be decoded. The index into the flag
string needed to be updated after parsing an argument.
Signed-off-by: Tim Chase <tim@chase2k.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4304
Gary Mills [Wed, 3 Feb 2016 00:23:21 +0000 (16:23 -0800)]
Illumos 6537 - Panic on zpool scrub with DEBUG kernel
6537 Panic on zpool scrub with DEBUG kernel
Reviewed by: Steve Gonczi <gonczi@comcast.net>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Matthew Ahrens <mahrens@delphix.com>
Dan McDonald [Wed, 3 Feb 2016 00:34:23 +0000 (16:34 -0800)]
Illumos 6096 - ZFS_SMB_ACL_RENAME needs to cleanup better
6096 ZFS_SMB_ACL_RENAME needs to cleanup better
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Gordon Ross <gordon.w.ross@gmail.com>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Approved by: Robert Mustacchi <rm@joyent.com>
6450 scrub/resilver unnecessarily traverses snapshots created
after the scrub started
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
Richard Sharpe [Sun, 24 Jan 2016 19:36:51 +0000 (11:36 -0800)]
Handling negative dentries in a CI file system.
For a Case Insensitive file system we must avoid creating negative
entries in the dentry cache. We must also pass the FIGNORECASE into
zfs_lookup so that special files are handled correctly.
We must also prevent negative dentries from being created when files are
unlinked.
Tested by running fsstress from LTP (10 loops, 10 processes, 10,000 ops.)
Also tested with printks (now removed) to ensure that lookups come to
zpl_lookup when negative should not exist.
Tests:
1. ls Some-file.txt; touch some-file.txt; ls Some-file.txt
and ensure no errors.
2. touch Some-file.txt; rm some-file.txt; ls Some-file.txt
and ensure that the last ls shows log messages showing the lookup
went all the way to zpl_lookup.
Thanks to tuxoko for helping me get this correct.
Signed-off-by: Richard Sharpe <realrichardsharpe@gmail.com> Signed-off-by: Chunwei Chen <tuxoko@gmail.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4243
Jorgen Lundman [Wed, 27 Jan 2016 02:02:04 +0000 (18:02 -0800)]
Illumos 6527 - Possible access beyond end of string in zpool comment
6527 Possible access beyond end of string in zpool comment
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Brian Behlendorf [Wed, 27 Jan 2016 01:54:45 +0000 (17:54 -0800)]
Illumos 6495 - Fix mutex leak in dmu_objset_find_dp
6495 Fix mutex leak in dmu_objset_find_dp
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Albert Lee <trisk@omniti.com>
Brian Behlendorf [Wed, 27 Jan 2016 01:27:46 +0000 (17:27 -0800)]
Illumos 6414 - vdev_config_sync could be simpler
6414 vdev_config_sync could be simpler
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Simon Klinkert [Sat, 23 Jan 2016 00:00:59 +0000 (16:00 -0800)]
llumos 6334 - Cannot unlink files when over quota
6334 Cannot unlink files when over quota
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Toomas Soome <tsoome@me.com>
Approved by: Dan McDonald <danmcd@omniti.com>
kernelOfTruth [Fri, 21 Aug 2015 01:43:10 +0000 (03:43 +0200)]
Reintroduce zfs_remove() synchronous deletes
Reintroduce a slightly adapted version of the Illumos logic for
synchronous unlinks. The basic idea here is that only files
smaller than zfs_delete_blocks (20480) blocks should be deleted
synchronously. Unlinking larger files should be handled
asynchronously to minimize impact to the caller.
To accomplish this iput() which is responsible for calling
zfs_znode_delete() on Linux is only called in the delete_now
path. Otherwise zfs_async_iput() is used which allows the
last reference to be dropped by a taskq thread effectively
making the removal asynchronous.
Porting notes:
- Add zfs_delete_blocks module option for performance analysis.
The default value is DMU_MAX_DELETEBLKCNT which is the same
as upstream. Reducing this value means that smaller files
will be unlinked asynchronously like large files.
- All occurrences of zfsvfs changes to zsb.
Ported-by: KernelOfTruth kerneloftruth@gmail.com Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Dan McDonald [Sun, 2 Aug 2015 13:01:14 +0000 (08:01 -0500)]
Log zvol truncate/discard operations
As the comments in zvol_discard() suggested, the discard operation
could be logged to the zil. This is a port of the relevant code from
Nexenta as it was added in "701 UNMAP support for COMSTAR" and has been
attributed to the author of that commit.
mount.zfs: use getopt_long instead of getopt to guarantee permutation of argv.
mount.zfs is called by convention (and util-linux) with arguments
last, i.e.
% mount.zfs <dataset> <mountpoint> -o <options>
This is not a problem on glibc since GNU getopt(3) will reorder the
arguments. However, alternative libc such as musl libc (or glibc with
$POSIXLY_CORRECT set) will not permute argv and fail to parse the -o
<options>. Use getopt_long so musl will permute arguments.
Signed-off-by: Christian Neukirchen <chneukirchen@gmail.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4222
Tim Chase [Sun, 24 Jan 2016 19:11:15 +0000 (13:11 -0600)]
Set arc_c_min properly in userland builds
Since it's set to arc_c_max / 2, it must be set after arc_c_max is set.
Also added protection against it falling below 2 * maxblocksize in
userland builds.
Signed-off-by: Tim Chase <tim@chase2k.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4268
Tim Chase [Fri, 22 Jan 2016 13:37:37 +0000 (07:37 -0600)]
Prevent arc_c collapse
Adjusting arc_c directly is racy because it can happen in the context
of multiple threads. It should always be >= 2 * maxblocksize. Set it
to a known valid value rather than adjusting it directly.
In addition refactor arc_shrink() to a simpler structure, protect against
underflow in the calculation of the new arc_c value.
Signed-off-by: Tim Chase <tim@chase2k.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reverts: 935434ef Closes: #3904 Closes: #4161
1778 Assertion failed: rn->rn_nozpool == B_FALSE
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george@delphix.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Approved by: Gordon Ross <gordon.ross@nexenta.com>
Porting notes:
- This change was originally never ported to Linux due to it
dependence on the thread pool interface. This patch solves
that issue by switching the code to use the existing taskq
implementation which provides the same basic functionality.
However, in order for this to work properly thread_init()
and thread_fini() must be called around to taskq consumer
to perform the needed thread initialization.
- The check_one_slice, nozpool_all_slices, and check_slices
functions have been disabled for Linux. They are difficult,
but possible, to implement for Linux due to how partitions
are get names. Since this is only an optimization this code
can be added at a latter date.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Matthew Ahrens [Mon, 7 Jul 2014 19:49:36 +0000 (11:49 -0800)]
Illumos 4950 - files sometimes can't be removed from a full filesystem
4950 files sometimes can't be removed from a full filesystem
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Boris Protopopov <bprotopopov@hotmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Porting notes:
- ZoL currently does not log discards to zvols, so the portion of
this patch that modifies the discard logging to mark it as
freeing space has been discarded.
2. may_delete_now had been removed from zfs_remove() in ZoL.
It has been reintroduced.
3. We do not try to emulate vnodes, so the following lines are
not valid on Linux:
Brian Behlendorf [Tue, 19 Jan 2016 18:41:21 +0000 (10:41 -0800)]
Close possible zfs_znode_held() race
Check if the lock is held while holding the z_hold_locks() lock.
This prevents a possible use-after-free bug for callers which are
not holding the lock. There currently are no such callers so this
can't cause a problem today but it has been fixed regardless.
Brian Behlendorf [Tue, 19 Jan 2016 17:04:44 +0000 (09:04 -0800)]
Linux 4.5 compat: pfn_t typedef
The pfn_t typedef was inherited from Illumos but never directly
used by any libspl consumers. This doesn't cause any issues in
user space but for consistency with the kernel build it has been
removed. See torvalds/linux/commit/34c0fd54.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Tim Chase <tim@chase2k.com> Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Issue #4228
Brian Behlendorf [Thu, 14 Jan 2016 23:01:24 +0000 (18:01 -0500)]
Linux 4.5 compat: xattr list handler
The registered xattr .list handler was simplified in the 4.5 kernel
to only perform a permission check. Given a dentry for the file it
must return a boolean indicating if the name is visible. This
differs slightly from the previous APIs which also required the
function to copy the name in to the provided list and return its
size. That is now all the responsibility of the caller.
This should be straight forward change to make to ZoL since we've
always required the caller to make the copy. However, this was
slightly complicated by the need to support 3 older APIs. Yes,
between 2.6.32 and 4.5 there are 4 versions of this interface!
Therefore, while the functional change in this patch is small it
includes significant cleanup to make the code understandable and
maintainable. These changes include:
- Improved configure checks for .list, .get, and .set interfaces.
- Interfaces checked from newest to oldest.
- Strict checking for each possible known interface.
- Configure fails when no known interface is available.
- HAVE_*_XATTR_LIST renamed HAVE_XATTR_LIST_* for consistency
with similar iops and fops configure checks.
- POSIX_ACL_XATTR_{DEFAULT|ACCESS} were removed forcing callers to
move to their replacements, XATTR_NAME_POSIX_ACL_{DEFAULT|ACCESS}.
Compatibility wrapper were added for old kernels.
- ZPL_XATTR_LIST_WRAPPER added which behaves the same as the existing
ZPL_XATTR_{GET|SET} WRAPPERs. Only the inode is guaranteed to be
a valid pointer, passing NULL for the 'list' and 'name' variables
is allowed and must be checked for. All .list functions were
updated to use the wrapper to aid readability.
- zpl_xattr_filldir() updated to use the .list function for its
permission check which is consistent with the updated Linux 4.5
interface. If a .list function is registered it should return 0
to indicate a name should be skipped, if there is no registered
function the name will be added.
- Additional documentation from xattr(7) describing the correct
behavior for each namespace was added before the relevant handlers.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Tim Chase <tim@chase2k.com> Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Issue #4228
Brian Behlendorf [Thu, 14 Jan 2016 18:25:10 +0000 (13:25 -0500)]
Linux 4.5 compat: get_link() / put_link()
The follow_link() interface was retired in favor of get_link().
In the process of phasing in get_link() the Linux kernel went
through two different versions. The first of which depended
on put_link() and the final version on a delayed done function.
- Improved configure checks for .follow_link, .get_link, .put_link.
- Interfaces checked from newest to oldest.
- Strict checking for each possible known interface.
- Configure fails when no known interface is available.
- Both versions .get_link are detected and supported as well
two previous versions of .follow_link.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Tim Chase <tim@chase2k.com> Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Issue #4228
Matthew Ahrens [Thu, 14 Jan 2016 00:10:38 +0000 (16:10 -0800)]
Illumos 4953, 4954, 4955
4953 zfs rename <snapshot> need not involve libshare
4954 "zfs create" need not involve libshare if we are not sharing
4955 libshare's get_zfs_dataset need not sort the datasets
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Gordon Ross <gordon.ross@nexenta.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Marcel Telka [Wed, 13 Jan 2016 23:35:55 +0000 (15:35 -0800)]
Illumos 4039 - zfs_rename()/zfs_link() needs stronger test for XDEV
4039 zfs_rename()/zfs_link() needs stronger test for XDEV
Reviewed by: Gordon Ross <gordon.ross@nexenta.com>
Reviewed by: Kevin Crowe <kevin.crowe@nexenta.com>
Reviewed by: Saso Kiselkov <skiselkov.ml@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@nexenta.com>
Porting notes:
- This check was updated in Linux in a similar fashion early on in
the port. Therefore, this patch just reorders the function and
updates the comment so it flows the same way as the upstream code.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4218
Joe Stein [Wed, 13 Jan 2016 23:05:59 +0000 (15:05 -0800)]
Illumos 6298 - zfs_create_008_neg and zpool_create_023_neg
6298 zfs_create_008_neg and zpool_create_023_neg need to be updated
for large block support
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
George Wilson [Wed, 13 Jan 2016 22:37:39 +0000 (14:37 -0800)]
Illumos 3557, 3558, 3559, 3560
3557 dumpvp_size is not updated correctly when a dump zvol's size is changed
3558 setting the volsize on a dump device does not return back ENOSPC
3559 setting a volsize larger than the space available sometimes succeeds
3560 dumpadm should be able to remove a dump device
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Albert Lee <trisk@nexenta.com>
Porting notes:
- Internal zvol.c changes not applied due to implementation differences.
The external interface and behavior was already consistent with the
latest upstream code.
- Retired 2.6.28 HAVE_CHECK_DISK_SIZE_CHANGE configure check. All
supported kernels (2.6.32 and newer) provide this interface.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #4217
Chunwei Chen [Wed, 30 Dec 2015 23:47:11 +0000 (15:47 -0800)]
Prevent duplicated xattr between SA and dir
When replacing an xattr would cause overflowing in SA, we would fallback
to xattr dir. However, current implementation don't clear the one in SA,
so we would end up with duplicated SA.
For example, running the following script on an xattr=sa filesystem
would cause duplicated "user.1".
-- dup_xattr.sh begin --
randbase64()
{
dd if=/dev/urandom bs=1 count=$1 2>/dev/null | openssl enc -a -A
}
Also, when a filesystem is switch from xattr=sa to xattr=on, it will
never modify those in SA. This would cause strange behavior like, you
cannot delete an xattr, or setxattr would cause duplicate and the result
would not match when you getxattr.
For example, the following shell sequence.
-- shell begin --
$ sudo zfs set xattr=sa pp/fs0
$ touch zzz
$ setfattr -n user.test -v asdf zzz
$ sudo zfs set xattr=on pp/fs0
$ setfattr -x user.test zzz
setfattr: zzz: No such attribute
$ getfattr -d zzz
user.test="asdf"
$ setfattr -n user.test -v zxcv zzz
$ getfattr -d zzz
user.test="asdf"
user.test="asdf"
-- shell end --
We fix this behavior, by first finding where the xattr resides before
setxattr. Then, after we successfully updated the xattr in one location,
we will clear the other location. Note that, because update and clear
are not in single tx, we could still end up with duplicated xattr. But
by doing setxattr again, it can be fixed.
Richard Yao [Tue, 28 Jul 2015 14:22:56 +0000 (10:22 -0400)]
Remove fastwrite mutex
The fast write mutex is intended to protect accounting, but it is
redundant because all accounting is performed through atomic operations.
It also serializes all metaslab IO behind a mutex, which introduces a
theoretical scaling regression that the Illumos developers did not like
when we showed this to them. Removing it makes the selection of the
metaslab_group lock free as it is on Illumos. The selection is not quite
the same without the lock because the loop races with IO completions,
but any imbalances caused by this are likely to be corrected by
subsequent metaslab group selections.
Signed-off-by: Richard Yao <ryao@gentoo.org> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #3643
Brian Behlendorf [Tue, 22 Dec 2015 21:47:38 +0000 (13:47 -0800)]
Fix zsb->z_hold_mtx deadlock
The zfs_znode_hold_enter() / zfs_znode_hold_exit() functions are used to
serialize access to a znode and its SA buffer while the object is being
created or destroyed. This kind of locking would normally reside in the
znode itself but in this case that's impossible because the znode and SA
buffer may not yet exist. Therefore the locking is handled externally
with an array of mutexs and AVLs trees which contain per-object locks.
In zfs_znode_hold_enter() a per-object lock is created as needed, inserted
in to the correct AVL tree and finally the per-object lock is held. In
zfs_znode_hold_exit() the process is reversed. The per-object lock is
released, removed from the AVL tree and destroyed if there are no waiters.
This scheme has two important properties:
1) No memory allocations are performed while holding one of the z_hold_locks.
This ensures evict(), which can be called from direct memory reclaim, will
never block waiting on a z_hold_locks which just happens to have hashed
to the same index.
2) All locks used to serialize access to an object are per-object and never
shared. This minimizes lock contention without creating a large number
of dedicated locks.
On the downside it does require znode_lock_t structures to be frequently
allocated and freed. However, because these are backed by a kmem cache
and very short lived this cost is minimal.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4106
Brian Behlendorf [Fri, 18 Dec 2015 20:19:14 +0000 (12:19 -0800)]
Add zfs_object_mutex_size module option
Add a zfs_object_mutex_size module option to facilitate resizing the
the per-dataset znode mutex array. Increasing this value may help
make the deadlock described in #4106 less common, but this is not a
proper fix. This patch is primarily to aid debugging and analysis.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Tim Chase <tim@chase2k.com>
Issue #4106
Brian Behlendorf [Wed, 13 Jan 2016 19:39:25 +0000 (11:39 -0800)]
Illumos 3465, 3466, 3467, 3468, 3470, 3473
3465 ::walk ... | ::<dcmd> misinterprets input as symbol names
3466 ::tsd should handle missing/NULL values better
3467 mdb_ctf_vread() could be more useful
3468 mdb enhancements for zfs development
3470 ::whatis does not print callers from KMF_LITE
3473 mdb_get_module() returns wrong module
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Approved by: Dan McDonald <danmcd@nexenta.com>