Ivan Grokhotkov [Fri, 22 Feb 2019 09:28:43 +0000 (17:28 +0800)]
nvs: do eager cleanup of HashListBlocks
Previously when HashList was removing items, HashListBlocks were
removed lazily. This resulted in empty HashListBlocks dangling around
in full pages, even when all items have been erased. These blocks
would only be deleted when NVS was re-initialized
(nvs_flash_deinit/nvs_flash_init).
This change does eager cleanup instead, based on the code from
@negativekelvin offered in
https://github.com/espressif/esp-idf/issues/1642#issuecomment-367227994.
Ivan Grokhotkov [Fri, 22 Feb 2019 13:27:43 +0000 (21:27 +0800)]
esp_timer: fix occasional failures in "monotonic values" test
1. ref_clock used in unit tests occasionally produces time off by ~100
microseconds shortly after being started. Add a delay to let
ref_clock stabilise, until the cause is found.
2. Reduce roundoff error accumulation which would occasionally cause
the test to fail, by choosing an overflow value which can be divided
by APB frequency.
3. Move time sampling part of the test into an IRAM function to
reduce variations due to cache behavior.
4. Remove calculation of "standard deviation" in the test, as what was
calculated was not actually standard deviation, and it did not add any
useful information.
Ivan Grokhotkov [Thu, 29 Nov 2018 07:18:11 +0000 (15:18 +0800)]
bootloader: check previously used clock frequency at run time
In the situation when bootloader was compiled for 240MHz, and app was
compiled for 160MHz, and the chip is a revision 0 chip, the
bootloader will assume that the application has also been running at
240MHz. This will cause the chip to lock up later. Modify this to use
a run time check of DPORT_CPUPERIOD_SEL, which indicates which of the
PLL frequencies was used.
Ivan Grokhotkov [Wed, 13 Feb 2019 03:40:48 +0000 (11:40 +0800)]
make: fix issues related to EXTRA_COMPONENT_DIRS
1. When one of the COMPONENT_DIRS points to a component directory
(i.e. a directory containing component.mk, not a directory of multiple
components), and there is a subdirectory in it which also contains
a component, the subdirectory was mistakenly added to the list of
components and compiled.
2. When one of the COMPONENT_DIRS points to a component directory, and
the parent directory contained a directory with the same name as
another component, that directory would be mistakenly added to the
COMPONENT_PATHS.
and Makefile sets EXTRA_COMPONENT_DIRS=$(realpath ../mycomponent),
then "esp32" directory which is at the same level as mycomponent
was added to COMPONENT_PATHS.
3. If EXTRA_COMPONENT_DIRS pointed to a directory with a list of
components, and one of the subdirectories was not a component, but
had the same name as another component, than that directory would be
mistakenly added to COMPONENT_PATHS instead of the real esp32
component directory.
For example:
my_components/
my_component/
component.mk
my_component.c
esp32/
(some random stuff)
and EXTRA_COMPONENT_DIRS would point to my_components/, then "esp32"
directory would be added to COMPONENT_PATHS instead of the real esp32
component directory.
1. In original driver, the stack size for emac driver task "emacT" is only 2048 Bytes, which also can not be changed by user.
2. Each time when invoking "emac_start" function, it will reset emac registers, the driver should reconfig some important registers again.
Tian Hao [Thu, 14 Feb 2019 08:37:56 +0000 (16:37 +0800)]
component/esp32 : fix coexist lc protect cause memory corrupted
The bug will cause memory corrupted (the largest range is from 0x3ffc0000 ~ 0x3ffc8000),
some strange error will happen, like IllegalInstruction, LoadProhibited and .etc.
Liu Zhi Fu [Thu, 31 Jan 2019 10:07:44 +0000 (18:07 +0800)]
esp32: fix some WiFi bugs
Fix following WiFi bugs:
1. Fix a crash bug which is caused by WiFi static TX buffer alloc/free.
2. Fix the bug that iphone fails to connect to ESP32 AP by enabling AP BAR receiving.
3. Fix the bug that ESP32 station fails to connect some APs, such as Xiaomi hotspot etc,
after reset.
Darian Leung [Fri, 4 Jan 2019 12:38:33 +0000 (20:38 +0800)]
freertos: Make backtrace work across interrupts (backport v3.1)
This commit adds the ability for backtracing to trace from the itnerrupt to the
task stack, and across nested interrupts. Test cases have also been added.
See merge request !4084
Note: "Test backtrace from abort" reset reason modified by removing abort as a reason.
David Cermak [Fri, 25 Jan 2019 16:19:13 +0000 (17:19 +0100)]
mdns: fixed crash on free undefined ptr after skipped strdup
Shortcircuit evaluation may cause skip of _mdns_strdup_check of any further question field, which after clear_rx_packet freed undefined memory.
Fixes https://ezredmine.espressif.cn:8765/issues/28465
Tian Hao [Wed, 23 Jan 2019 06:11:56 +0000 (14:11 +0800)]
component/bt: add a option to make report adv data and scan response individually
Originally, when doing BLE active scan, Bluedroid will not report adv to
application layer until receive scan response. This option is used to
disable the behavior. When enable this option, Bluedroid will report
adv data or scan response to application layer immediately.
Angus Gratton [Fri, 21 Dec 2018 04:37:57 +0000 (15:37 +1100)]
hwcrypto sha: Allow SHA contexts to be shared between tasks
Previously, hardware SHA engine "locks" were mutex semaphores. This meant that the task which
started a particular SHA session (in hardware) needed to finalise that session, or an invalid
FreeRTOS state was created.
Replace with binary semaphore which can be shared between tasks.
Includes a unit test, but unit test doesn't crash even without this fix
(some other unknown condition is required).
Ivan Grokhotkov [Mon, 3 Sep 2018 10:15:20 +0000 (18:15 +0800)]
bootloader: account for load address when mapping cache pages
Bootloader used to calculate the number of cache pages assuming that
load address was aligned, while in reality load address for DROM and
IROM was offset by 0x20 bytes from the start of 64kB page. This
caused the bootloader to map one less page if the size of the image
was 0x4..0x1c less than a multiple of 64kB.
Reported in https://esp32.com/viewtopic.php?f=13&t=6952.
Ivan Grokhotkov [Wed, 26 Sep 2018 12:46:15 +0000 (20:46 +0800)]
esp32: remove ROM functions redefined in IDF from LD script
In some cases, linker could choose to use ROM functions instead of the
ones defined in IDF.
For functions used in ROM stub table, this would lead to infinite
recursion when the corresponding function was called from ROM.
For crypto functions, some of these were modified in IDF, and
incompatible with ROM counterparts.
Ivan Grokhotkov [Thu, 1 Nov 2018 03:30:48 +0000 (11:30 +0800)]
bootloader, esp32: add workaround for Tensilica erratum 572
If zero-overhead loop buffer is enabled, under certain rare conditions
when executing a zero-overhead loop, the CPU may attempt to execute an invalid instruction. Work around by disabling the buffer.
1. Change bus reset to handle interrupted READ sequences.
2. Slow down I2C to 100khz during reset
3. If a SLAVE device was in a read operation when the bus was interrupted, the SLAVE device is controlling SDA.The only bit during the 9 clock cycles of a byte READ the MASTER(ESP32) is guaranteed control over, is during the ACK bit period.
If the SLAVE is sending a stream of ZERO bytes, it will only release SDA during the ACK bit period. The master(ESP32) cannot generate a STOP unless SDA is HIGH. So, this reset code synchronizes the bit stream with, Either, the ACK bit, Or a 1 bit.
I am stealing this delay coding from @jeremyherbert #2493 pr.
2. Change Bus Reset to handle interrupted READ sequences.
The current code does not handle interrupted READ cycles.
If a SLAVE device was in a read operation when the bus was interrupted, the SLAVE device is controlling SDA.
The only bit during the 9 clock cycles of a byte READ the MASTER(ESP32) is guaranteed control over, is during the ACK bit period.
If the SLAVE is sending a stream of ZERO bytes, it will only release SDA during the ACK bit period. The master(ESP32) cannot generate a STOP unless SDA is HIGH.
So, this reset code synchronizes the bit stream with, Either, the ACK bit, Or a 1 bit.
3. fix typo
correct `sda_id` to `sda_io` in `i2c_master_clear_bus()` @ryan-ma found it. This typo was generated when I manually edited this patch on GitHub, I should have done a Copy/Paste operation!
Tian Hao [Sun, 13 Jan 2019 08:05:12 +0000 (16:05 +0800)]
Fix some bugs in phy
1. fix bug PHY/RTC functions called in ISR (update phy to v4007)
2. add UnitTest to test it
3. fix task watchdog bug when wifi change channel
4. disable/enable agc to mac deinit/init
5. add UnitTest Job
XiaXiaotian [Thu, 27 Dec 2018 09:40:56 +0000 (17:40 +0800)]
esp32: unforce wifi if receiving beacon with no data buffered in dream
state and reduce force receiving broadcast data time
1. If receiving beacon which indicates that there is no data
buffered, do not force to receive WiFi data.
2. If receiving beacon which indicates that there is broadcast data
buffered, reduce the time to force receiving broadcast data.
projects / esp-idf / log