David Cermak [Fri, 25 Jan 2019 19:24:30 +0000 (20:24 +0100)]
mdns tests: execute test services only when running example in ci
Test services may cause confussion (and did cause some GitHub/forum issues). This update runs test services only when example executed in ci. Also host name is a simple config entry if executed outside of ci.
David Cermak [Fri, 25 Jan 2019 15:17:07 +0000 (16:17 +0100)]
mdns: fix crash after init if no memory for task
mdns init first starts timer task, then starts service task. if service task failed to be created, timer task needs to be stopped too.
fixed https://ezredmine.espressif.cn:8765/issues/28466
David Cermak [Fri, 25 Jan 2019 16:19:13 +0000 (17:19 +0100)]
mdns: fixed crash on free undefined ptr after skipped strdup
Shortcircuit evaluation may cause skip of _mdns_strdup_check of any further question field, which after clear_rx_packet freed undefined memory.
Fixes https://ezredmine.espressif.cn:8765/issues/28465
Darian Leung [Fri, 4 Jan 2019 12:38:33 +0000 (20:38 +0800)]
freertos: Make backtrace work across interrupts
This commit adds the ability for backtracing to trace from the itnerrupt to the
task stack, and across nested interrupts. Test cases have also been added.
michael [Fri, 21 Sep 2018 08:48:04 +0000 (16:48 +0800)]
spi: add new test for timing and mode
New unit tests added
------------------------
**Local:** Local test uses the GPIO matrix to connect the master and the
slave on the same board. When the master needs the iomux, the master
uses the GPIOs of its own, the slave connect to the pins by GPIO matrix;
When the slave needs the iomux, the slave uses the GPIOs of its own, the
master connects to the pins by GPIO matrix.
- Provide a new unit test which performs freq scanning in mode 0. It
scans frequency of 1M, 8M, 9M and all frequency steps up to the maximum
frequency allowed.
**M & S**: Master & slave tests performs the test with two boards. The
master and slave use iomux or gpio matrix according to the config.
- Provide a new unit test which performs freq scanning in mode 0. It
scans frequency of 1M, 8M, 9M and all frequency steps up to the maximum
frequency allowed.
- Provide a new unit test which performs mode test with significant
frequencies. It tests mode 0,1,2,3 with low frequency, and the maximum
frequency allowed.
michael [Mon, 25 Jun 2018 04:34:31 +0000 (12:34 +0800)]
spi_slave: improve the timing configuration
SPI Slave
===========
- Correct the configuration of mode 0~3 using new config in the TRM
- Split the workaround for DMA in mode 0/2 out of normal config, to make it clear.
- Update timing and speed document for the SPI slave.
michael [Tue, 26 Jun 2018 08:23:39 +0000 (16:23 +0800)]
test: add new test framework for different configurations
Paremeterized Test Framework
-----------------------------
The SPI has a lot of parameters, which works in the same process.
This framework provides a way to easily test different parameter sets.
The framework can work in two different ways:
- local test: which requires only one board to perform the test - master
& slave test: which generates two sub test items which uses the same
config set to cooperate to perform the test.
The user defines a (pair if master/slave) set of init/deinit/loop
functions. Then the test framework will call init once, then call loop
several times with different configurations, then call deinit.
Then a unit test can be appended by add a parameter group, and pass it into
a macro.
qiyueixa [Thu, 24 Jan 2019 07:15:09 +0000 (15:15 +0800)]
mesh: udpate libs
1. during parent selection, when scanning a MAP without ext-assoc IE, it will be handled as it has the same router BSSID as itself.
2. for MAP, when its client leaves, always post SYSTEM_EVENT_AP_STADISCONNECTED to mesh layer regardless of whether the client has passed the encrypted authentication or not.
Tian Hao [Wed, 23 Jan 2019 06:11:56 +0000 (14:11 +0800)]
component/bt: add a option to make report adv data and scan response individually
Originally, when doing BLE active scan, Bluedroid will not report adv to
application layer until receive scan response. This option is used to
disable the behavior. When enable this option, Bluedroid will report
adv data or scan response to application layer immediately.
Pieter du Preez [Mon, 24 Dec 2018 11:37:09 +0000 (11:37 +0000)]
Initialized some uninitialized variables in rtc_clk.c and ringbuf.c.
The following 2 compiler warnings are only reproducible when setting:
OPTIMIZATION_FLAGS = -Ofast
esp-idf/components/soc/esp32/rtc_clk.c:
In function 'rtc_clk_cpu_freq_get':
esp-idf/components/soc/esp32/rtc_clk.c:506:12:
error: 'freq' may be used uninitialized in this function
[-Werror=maybe-uninitialized]
return freq;
esp-idf/components/esp_ringbuf/ringbuf.c:
In function 'xRingbufferReceiveSplitFromISR':
esp-idf/components/esp_ringbuf/ringbuf.c:934:26:
error: 'pvTempTailItem' may be used uninitialized in this function
[-Werror=maybe-uninitialized]
*ppvTailItem = pvTempTailItem;
morris [Fri, 23 Nov 2018 03:53:20 +0000 (11:53 +0800)]
modem: support modem facility and PPPoS
1. add support for ESP32 DTE
2. add support for SIM800/BG96 DCE
3. add PPPoS setup procedure
4. add support for SMS
5. add mqtt example after PPP connection established
Angus Gratton [Fri, 21 Dec 2018 04:37:57 +0000 (15:37 +1100)]
hwcrypto sha: Allow SHA contexts to be shared between tasks
Previously, hardware SHA engine "locks" were mutex semaphores. This meant that the task which
started a particular SHA session (in hardware) needed to finalise that session, or an invalid
FreeRTOS state was created.
Replace with binary semaphore which can be shared between tasks.
Includes a unit test, but unit test doesn't crash even without this fix
(some other unknown condition is required).
Sagar Bijwe [Fri, 11 Jan 2019 06:29:59 +0000 (11:59 +0530)]
CMake: Make IDF_PATH available to Kconfiglib when not explicitly set.
When IDF_PATH is not set by the user, cmake infers the same through
other means and sets it as an environment variable. However, some
sub-invocation of cmake may not see this variable as it is not set
in the parent. This change adds a custom command for exporting IDF_PATH
just before invoking ldgen so that IDF_PATH can be used in Kconfig
without any errors.
projects / esp-idf / log