Peter Boström [Thu, 31 Aug 2017 21:33:59 +0000 (14:33 -0700)]
Prevent data race from low-pass filter.
Makes main thread wait for the filter level to be picked to avoid a race
between the LPF thread and update_reference_frames(). This also
re-enables the failing tests under thread_sanitizer where this data race
was detected.
Peter Boström [Fri, 25 Aug 2017 22:48:11 +0000 (15:48 -0700)]
Add atomics to vp8 synchronization primitives.
Fixes issue on iPad Pro 10.5 (and probably other places) where threads
are not properly synchronized. On x86 this data race was benign as load
and store instructions are atomic, they were being atomic in practice as
the program hasn't been observed to be miscompiled.
Such guarantees are not made outside x86, and real problems manifested
where libvpx reliably reproduced a broken bitstream for even just the
initial keyframe. This was detected in WebRTC where this device started
using multithreading (as its CPU count is higher than earlier devices,
where the problem did not manifest as single-threading was used in
practice).
This issue was not detected under thread-sanitizer bots as mutexes were
conditionally used under this platform to simulate the protected read
and write semantics that were in practice provided on x86 platforms.
This change also removes several mutexes, so encoder/decoder state is
lighter-weight after this change and we do not need to initialize so
many mutexes (this was done even on non-thread-sanitizer platforms where
they were unused).
Re-enabled tests still fail tsan in high bitdepth.
Original change's description:
> Re-enable disabled tests under TSan.
>
> These tests point to an already-fixed bug, this should no longer have a
> data race.
>
> BUG=webm:1049
>
> Change-Id: Iaedc5db8df99362bdc501b70ff7fdebf8756fdb8
Marco [Mon, 21 Aug 2017 23:39:56 +0000 (16:39 -0700)]
vp9: Speed 6 adapt_partition for live/vbr usage.
Enable adapt_partition for vbr mode for speed 6.
This allows the usage of the pickmode-based partition
(used in speed 5), but only selectively for superblocks
with high source sad, otherwise the faster variance based
partition scheme is used.
For speed 6 on ytlive set: avgPSNR/SSIM metrics up by ~0.6%,
several clips up by ~1.5%. Small/negligible decrease in speed.
Reason for revert: <INSERT REASONING HERE>
Failures in AVX/VP9QuantizeTest in nightly tests.
Original change's description:
> quantize avx: copy 32x32 implementation
>
> Ensure avx and ssse3 stay in sync by testing them against each other.
>
> Change-Id: I699f3b48785c83260825402d7826231f475f697c
Marco [Thu, 24 Aug 2017 17:36:27 +0000 (10:36 -0700)]
vp9: Adjust 16x16 splot threshold for variance partition
For speeds < 7, increase threshold that controls the split
of 16x16->8x8 blocks, for resolutions 720p and higher.
Minor change for speed 5 (since it uses reference partition scheme
which only uses variance partition as first step).
For speed 6: ~0.5% increase in avgPSNR/SSIM metrics on ytlvie set.
No change in speed.
Johann [Tue, 22 Aug 2017 22:43:35 +0000 (15:43 -0700)]
quantize avx: copy implementation to intrinsics
Adds an early exit based on ptest. Slightly slower than ssse3 in the
full case because of the extra check, but potentially faster if lots of
rows can be skipped.
Very close in speed to the assembly.
Can run in 32 bit, unlike the assembly. Allows reworking the function
prototype to use structs.
* changes:
quantize: ignore skip_block in arm
quantize: ignore skip_block in x86
quantize fp: ignore skip_block in arm
quantize fp: ignore skip_block in x86
Johann [Wed, 16 Aug 2017 20:34:14 +0000 (13:34 -0700)]
Remove skip_block from quantize
This condition is handled before this code is reached. The ssse3 version
of the function has always crashed when attempting to handle the
skip_block condition.
Add assert() and comments regarding the usage of skip_block.
Removing the parameter is a fairly involved process so leave it be for
the moment.
paulwilkins [Wed, 16 Aug 2017 12:34:49 +0000 (13:34 +0100)]
Prevent parameters that can cause invalid ARF groups.
Having a very low "lag_in_frames" value could cause the encoder to create
incorrect / corrupt ARF groups including displayed frames that update the
ARF buffer and false overlay frames that are coded at low rate but are not
actually overlays of a real ARF frame.
This is linked to a reported unit test "slow down" where the chosen parameters
(lag of 3 frames) gave rise to such "broken" ARF group(s).
paulwilkins [Wed, 16 Aug 2017 13:07:24 +0000 (14:07 +0100)]
Fix corrupt arf groups due to low "lag_in_frames"
Having a very small value for "lag_in_frames" can result in
corrupt arf groups including displayed frames that update
the arf buffer and fake overlay frames that are not in fact
overlays of real arfs but are nevertheless starved of bits.
Leaving lag_in_frames at the default of 25 for these 5 frame two
pass VBR tests should now give rise to a valid ARF coding pattern
as follows:- K(ey), A(rf), N(ormal), N, N, O(verlay).
This change is part of a response to BUG=webm:1454 where broken
arf groups interacted badly with a change that corrects for large rate
misses. However, it may still in some cases increase encode time by
virtue of the fact that the unit test now codes a correct coding pattern
with "hidden" ARF frames.
paulwilkins [Mon, 14 Aug 2017 15:11:34 +0000 (16:11 +0100)]
Fix for encoder slowdown (for speeds >= 3)
Some clips in nightly unit test exhibiting significant encoder slowdown which
appears to bisect to Change-Id: I692311a709ccdb6003e705103de9d05b59bf840a.
The above change allowed for emergency iterations of the recode loop and
adjustment of the Q range if there is a large rate miss.
This patch disables the above adaptation for cases of cpu_speed >= 3 or more
specifically where cpi->sf.recode_loop >= ALLOW_RECODE_KFARFGF.
For speeds >= 3 the code does not currently run a dummy bit pack operation
inside the recode loop. Without this dummy pack operation there is no up to
date estimate of the current frame's size to use as a basis for assessing the
requirement for a recode. In practice it was using the previous frames size (or 0
for the first frame) which could cause odd behavior.
If we require the emergency rate correction added in Change-Id: I6923.. for
the higher speed settings it will be necessary to enable the dummy pack
which will in turn hurt encode speed.
Jerome Jiang [Mon, 14 Aug 2017 18:55:42 +0000 (11:55 -0700)]
vp9 svc: Fix the stats output when sl = 1.
Actual frame size and bitrate is all 0 when using SVC sample encoder
with sl = 1 because the stats are set in parse_superframe_index which
will not caculate properly when sl = 1 since there is no superframe.