Updated sigma-delta example description to the latest template

diff --git a/examples/peripherals/sigmadelta/README.md b/examples/peripherals/sigmadelta/README.md
index 669e65a0e5d25135ad56132f388d25697f8c5cdf..ab830f83ca6f146613d62601162072d53edaadaf 100644 (file)
--- a/examples/peripherals/sigmadelta/README.md
+++ b/examples/peripherals/sigmadelta/README.md
@@ -1,7 +1,71 @@
-# Example: sigma_delta modulation
+# Sigma Delta Modulation Example
 
-This example uses the sigma-delta driver to generate modulated output on a GPIO.
+(See the README.md file in the upper level 'examples' directory for more information about examples.)
 
-By default the GPIO output is 4, however you can edit this in the `sigmadelta_init()` function inside `main/sigmadelta_test.c`.
+This example uses the sigma-delta driver to generate modulated output on a GPIO. If you connect a LED to the output GPIO, you will see it slowly brightening and dimming.
 
-If you connect a LED to the output GPIO, you will see it blinking slowly.
+
+## How to use example
+
+### Hardware Required
+
+Besides the ESP32 board you need a LED and a resister to limit the LED current. Connect them as below:
+
+```
+             330R            LED     
+GPIO4 +----/\/\/\----+------|>|-----+ GND
+```
+
+A resistor in range from 100 Ohm to 1 kOhm should usually be fine.
+
+By default the GPIO output is 4. To change it, edit the line with `GPIO_NUM_4` in `sigmadelta_init()` function inside `main/sigmadelta_test.c`. For example to use GPIO 25, modify the line to contain `GPIO_NUM_25` instead.
+
+
+### Configure the project
+
+```
+make menuconfig
+```
+
+Set serial port under Serial Flasher Options and save the configuration.
+
+
+### Build and Flash
+
+Build the project and flash it to the board, then run monitor tool to view serial output:
+
+```
+make -j4 flash monitor
+```
+
+(To exit the serial monitor, type ``Ctrl-]``.)
+
+See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
+
+## Example Output
+
+Once the upload is complete and the board is reset, the program should start running. This is reported on the monitor as below:
+
+```
+...
+I (275) cpu_start: Pro cpu start user code
+I (293) cpu_start: Starting scheduler on PRO CPU.
+I (0) cpu_start: Starting scheduler on APP CPU.
+```
+
+Immediately after that the LED should start brightening and dimming.
+
+
+## Troubleshooting
+
+If you are using [ESP-WROVER-KIT](https://www.espressif.com/en/products/hardware/esp-wrover-kit/overview) then this board has a RGB LED already installed. GPIO4 is driving blue color of the LED. The brightening and dimming effect of the blue LED may not be distinctly visible because red and green LEDs are not actively driven and will slightly lit. To resolve this issue you can switch both diodes off by adding the following code at the end of `sigmadelta_example_init()` function:
+
+```c
+gpio_pad_select_gpio(GPIO_NUM_0);
+gpio_set_direction(GPIO_NUM_0, GPIO_MODE_OUTPUT);
+gpio_set_level(GPIO_NUM_0, 0);
+
+gpio_pad_select_gpio(GPIO_NUM_2);
+gpio_set_direction(GPIO_NUM_2, GPIO_MODE_OUTPUT);
+gpio_set_level(GPIO_NUM_2, 0);
+```

diff --git a/examples/peripherals/sigmadelta/main/sigmadelta_example_main.c b/examples/peripherals/sigmadelta/main/sigmadelta_example_main.c
index 594dbdb0c40688d67883326c98a2d9466790cf30..38bf2c099170578a7d9ec1f1134f0ea5b4e207bc 100644 (file)
--- a/examples/peripherals/sigmadelta/main/sigmadelta_example_main.c
+++ b/examples/peripherals/sigmadelta/main/sigmadelta_example_main.c
@@ -26,7 +26,7 @@ static void sigmadelta_example_init(void)
         .channel = SIGMADELTA_CHANNEL_0,
         .sigmadelta_prescale = 80,
         .sigmadelta_duty = 0,
-        .sigmadelta_gpio = 4,
+        .sigmadelta_gpio = GPIO_NUM_4,
     };
     sigmadelta_config(&sigmadelta_cfg);
 }