1 /******************************************************************************
3 * Copyright (C) 1999-2012 Broadcom Corporation
5 * Licensed under the Apache License, Version 2.0 (the "License");
6 * you may not use this file except in compliance with the License.
7 * You may obtain a copy of the License at:
9 * http://www.apache.org/licenses/LICENSE-2.0
11 * Unless required by applicable law or agreed to in writing, software
12 * distributed under the License is distributed on an "AS IS" BASIS,
13 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
14 * See the License for the specific language governing permissions and
15 * limitations under the License.
17 ******************************************************************************/
19 /******************************************************************************
21 * This file contains L2CAP internal definitions
23 ******************************************************************************/
33 #include "fixed_queue.h"
35 #define L2CAP_MIN_MTU 48 /* Minimum acceptable MTU is 48 bytes */
37 /* Timeouts. Since L2CAP works off a 1-second list, all are in seconds.
39 #define L2CAP_LINK_ROLE_SWITCH_TOUT 10 /* 10 seconds */
40 #define L2CAP_LINK_CONNECT_TOUT 60 /* 30 seconds */
41 #define L2CAP_LINK_CONNECT_TOUT_EXT 120 /* 120 seconds */
42 #define L2CAP_ECHO_RSP_TOUT 30 /* 30 seconds */
43 #define L2CAP_LINK_FLOW_CONTROL_TOUT 2 /* 2 seconds */
44 #define L2CAP_LINK_DISCONNECT_TOUT 30 /* 30 seconds */
46 #ifndef L2CAP_CHNL_CONNECT_TOUT /* BTIF needs to override for internal project needs */
47 #define L2CAP_CHNL_CONNECT_TOUT 60 /* 60 seconds */
50 #define L2CAP_CHNL_CONNECT_TOUT_EXT 120 /* 120 seconds */
51 #define L2CAP_CHNL_CFG_TIMEOUT 30 /* 30 seconds */
52 #define L2CAP_CHNL_DISCONNECT_TOUT 10 /* 10 seconds */
53 #define L2CAP_DELAY_CHECK_SM4 2 /* 2 seconds */
54 #define L2CAP_WAIT_INFO_RSP_TOUT 3 /* 3 seconds */
55 #define L2CAP_WAIT_UNPARK_TOUT 2 /* 2 seconds */
56 #define L2CAP_LINK_INFO_RESP_TOUT 2 /* 2 seconds */
57 #define L2CAP_UPDATE_CONN_PARAM_TOUT 6 /* 6 seconds */
58 #define L2CAP_BLE_LINK_CONNECT_TOUT 30 /* 30 seconds */
59 #define L2CAP_BLE_CONN_PARAM_UPD_TOUT 30 /* 30 seconds */
61 /* quick timer uses millisecond unit */
62 #define L2CAP_DEFAULT_RETRANS_TOUT 2000 /* 2000 milliseconds */
63 #define L2CAP_DEFAULT_MONITOR_TOUT 12000 /* 12000 milliseconds */
64 #define L2CAP_FCR_ACK_TOUT 200 /* 200 milliseconds */
66 /* Define the possible L2CAP channel states. The names of
67 ** the states may seem a bit strange, but they are taken from
68 ** the Bluetooth specification.
71 CST_CLOSED, /* Channel is in clodes state */
72 CST_ORIG_W4_SEC_COMP, /* Originator waits security clearence */
73 CST_TERM_W4_SEC_COMP, /* Acceptor waits security clearence */
74 CST_W4_L2CAP_CONNECT_RSP, /* Waiting for peer conenct response */
75 CST_W4_L2CA_CONNECT_RSP, /* Waiting for upper layer connect rsp */
76 CST_CONFIG, /* Negotiating configuration */
77 CST_OPEN, /* Data transfer state */
78 CST_W4_L2CAP_DISCONNECT_RSP, /* Waiting for peer disconnect rsp */
79 CST_W4_L2CA_DISCONNECT_RSP /* Waiting for upper layer disc rsp */
82 /* Define the possible L2CAP link states
87 LST_CONNECTING_WAIT_SWITCH,
95 /* Define input events to the L2CAP link and channel state machines. The names
96 ** of the events may seem a bit strange, but they are taken from
97 ** the Bluetooth specification.
99 #define L2CEVT_LP_CONNECT_CFM 0 /* Lower layer connect confirm */
100 #define L2CEVT_LP_CONNECT_CFM_NEG 1 /* Lower layer connect confirm (failed) */
101 #define L2CEVT_LP_CONNECT_IND 2 /* Lower layer connect indication */
102 #define L2CEVT_LP_DISCONNECT_IND 3 /* Lower layer disconnect indication */
103 #define L2CEVT_LP_QOS_CFM 4 /* Lower layer QOS confirmation */
104 #define L2CEVT_LP_QOS_CFM_NEG 5 /* Lower layer QOS confirmation (failed)*/
105 #define L2CEVT_LP_QOS_VIOLATION_IND 6 /* Lower layer QOS violation indication */
107 #define L2CEVT_SEC_COMP 7 /* Security cleared successfully */
108 #define L2CEVT_SEC_COMP_NEG 8 /* Security procedure failed */
110 #define L2CEVT_L2CAP_CONNECT_REQ 10 /* Peer connection request */
111 #define L2CEVT_L2CAP_CONNECT_RSP 11 /* Peer connection response */
112 #define L2CEVT_L2CAP_CONNECT_RSP_PND 12 /* Peer connection response pending */
113 #define L2CEVT_L2CAP_CONNECT_RSP_NEG 13 /* Peer connection response (failed) */
114 #define L2CEVT_L2CAP_CONFIG_REQ 14 /* Peer configuration request */
115 #define L2CEVT_L2CAP_CONFIG_RSP 15 /* Peer configuration response */
116 #define L2CEVT_L2CAP_CONFIG_RSP_NEG 16 /* Peer configuration response (failed) */
117 #define L2CEVT_L2CAP_DISCONNECT_REQ 17 /* Peer disconnect request */
118 #define L2CEVT_L2CAP_DISCONNECT_RSP 18 /* Peer disconnect response */
119 #define L2CEVT_L2CAP_INFO_RSP 19 /* Peer information response */
120 #define L2CEVT_L2CAP_DATA 20 /* Peer data */
122 #define L2CEVT_L2CA_CONNECT_REQ 21 /* Upper layer connect request */
123 #define L2CEVT_L2CA_CONNECT_RSP 22 /* Upper layer connect response */
124 #define L2CEVT_L2CA_CONNECT_RSP_NEG 23 /* Upper layer connect response (failed)*/
125 #define L2CEVT_L2CA_CONFIG_REQ 24 /* Upper layer config request */
126 #define L2CEVT_L2CA_CONFIG_RSP 25 /* Upper layer config response */
127 #define L2CEVT_L2CA_CONFIG_RSP_NEG 26 /* Upper layer config response (failed) */
128 #define L2CEVT_L2CA_DISCONNECT_REQ 27 /* Upper layer disconnect request */
129 #define L2CEVT_L2CA_DISCONNECT_RSP 28 /* Upper layer disconnect response */
130 #define L2CEVT_L2CA_DATA_READ 29 /* Upper layer data read */
131 #define L2CEVT_L2CA_DATA_WRITE 30 /* Upper layer data write */
132 #define L2CEVT_L2CA_FLUSH_REQ 31 /* Upper layer flush */
134 #define L2CEVT_TIMEOUT 32 /* Timeout */
135 #define L2CEVT_SEC_RE_SEND_CMD 33 /* btm_sec has enough info to proceed */
137 #define L2CEVT_ACK_TIMEOUT 34 /* RR delay timeout */
140 /* Bitmask to skip over Broadcom feature reserved (ID) to avoid sending two
141 successive ID values, '0' id only or both */
142 #define L2CAP_ADJ_BRCM_ID 0x1
143 #define L2CAP_ADJ_ZERO_ID 0x2
144 #define L2CAP_ADJ_ID 0x3
146 /* Return values for l2cu_process_peer_cfg_req() */
147 #define L2CAP_PEER_CFG_UNACCEPTABLE 0
148 #define L2CAP_PEER_CFG_OK 1
149 #define L2CAP_PEER_CFG_DISCONNECT 2
151 /* eL2CAP option constants */
152 #define L2CAP_MIN_RETRANS_TOUT 2000 /* Min retransmission timeout if no flush timeout or PBF */
153 #define L2CAP_MIN_MONITOR_TOUT 12000 /* Min monitor timeout if no flush timeout or PBF */
155 #define L2CAP_MAX_FCR_CFG_TRIES 2 /* Config attempts before disconnecting */
157 typedef uint8_t tL2C_BLE_FIXED_CHNLS_MASK;
160 UINT8 next_tx_seq; /* Next sequence number to be Tx'ed */
161 UINT8 last_rx_ack; /* Last sequence number ack'ed by the peer */
162 UINT8 next_seq_expected; /* Next peer sequence number expected */
163 UINT8 last_ack_sent; /* Last peer sequence number ack'ed */
164 UINT8 num_tries; /* Number of retries to send a packet */
165 UINT8 max_held_acks; /* Max acks we can hold before sending */
167 BOOLEAN remote_busy; /* TRUE if peer has flowed us off */
168 BOOLEAN local_busy; /* TRUE if we have flowed off the peer */
170 BOOLEAN rej_sent; /* Reject was sent */
171 BOOLEAN srej_sent; /* Selective Reject was sent */
172 BOOLEAN wait_ack; /* Transmitter is waiting ack (poll sent) */
173 BOOLEAN rej_after_srej; /* Send a REJ when SREJ clears */
175 BOOLEAN send_f_rsp; /* We need to send an F-bit response */
177 UINT16 rx_sdu_len; /* Length of the SDU being received */
178 BT_HDR *p_rx_sdu; /* Buffer holding the SDU being received */
179 fixed_queue_t *waiting_for_ack_q; /* Buffers sent and waiting for peer to ack */
180 fixed_queue_t *srej_rcv_hold_q; /* Buffers rcvd but held pending SREJ rsp */
181 fixed_queue_t *retrans_q; /* Buffers being retransmitted */
183 TIMER_LIST_ENT ack_timer; /* Timer delaying RR */
184 TIMER_LIST_ENT mon_retrans_timer; /* Timer Monitor or Retransmission */
186 #if (L2CAP_ERTM_STATS == TRUE)
187 UINT32 connect_tick_count; /* Time channel was established */
188 UINT32 ertm_pkt_counts[2]; /* Packets sent and received */
189 UINT32 ertm_byte_counts[2]; /* Bytes sent and received */
190 UINT32 s_frames_sent[4]; /* S-frames sent (RR, REJ, RNR, SREJ) */
191 UINT32 s_frames_rcvd[4]; /* S-frames rcvd (RR, REJ, RNR, SREJ) */
192 UINT32 xmit_window_closed; /* # of times the xmit window was closed */
193 UINT32 controller_idle; /* # of times less than 2 packets in controller */
194 /* when the xmit window was closed */
195 UINT32 pkts_retransmitted; /* # of packets that were retransmitted */
196 UINT32 retrans_touts; /* # of retransmission timouts */
197 UINT32 xmit_ack_touts; /* # of xmit ack timouts */
199 #define L2CAP_ERTM_STATS_NUM_AVG 10
200 #define L2CAP_ERTM_STATS_AVG_NUM_SAMPLES 100
201 UINT32 ack_delay_avg_count;
202 UINT32 ack_delay_avg_index;
203 UINT32 throughput_start;
204 UINT32 throughput[L2CAP_ERTM_STATS_NUM_AVG];
205 UINT32 ack_delay_avg[L2CAP_ERTM_STATS_NUM_AVG];
206 UINT32 ack_delay_min[L2CAP_ERTM_STATS_NUM_AVG];
207 UINT32 ack_delay_max[L2CAP_ERTM_STATS_NUM_AVG];
208 UINT32 ack_q_count_avg[L2CAP_ERTM_STATS_NUM_AVG];
209 UINT32 ack_q_count_min[L2CAP_ERTM_STATS_NUM_AVG];
210 UINT32 ack_q_count_max[L2CAP_ERTM_STATS_NUM_AVG];
215 /* Define a registration control block. Every application (e.g. RFCOMM, SDP,
216 ** TCS etc) that registers with L2CAP is assigned one of these.
218 #if (L2CAP_UCD_INCLUDED == TRUE)
219 #define L2C_UCD_RCB_ID 0x00
220 #define L2C_UCD_STATE_UNUSED 0x00
221 #define L2C_UCD_STATE_W4_DATA 0x01
222 #define L2C_UCD_STATE_W4_RECEPTION 0x02
223 #define L2C_UCD_STATE_W4_MTU 0x04
227 tL2CAP_UCD_CB_INFO cb_info;
234 UINT16 real_psm; /* This may be a dummy RCB for an o/b connection but */
235 /* this is the real PSM that we need to connect to */
236 #if (L2CAP_UCD_INCLUDED == TRUE)
240 tL2CAP_APPL_INFO api;
244 #ifndef L2CAP_CBB_DEFAULT_DATA_RATE_BUFF_QUOTA
245 #define L2CAP_CBB_DEFAULT_DATA_RATE_BUFF_QUOTA 100
247 /* Define a channel control block (CCB). There may be many channel control blocks
248 ** between the same two Bluetooth devices (i.e. on the same link).
249 ** Each CCB has unique local and remote CIDs. All channel control blocks on
250 ** the same physical link and are chained together.
252 typedef struct t_l2c_ccb {
253 BOOLEAN in_use; /* TRUE when in use, FALSE when not */
254 tL2C_CHNL_STATE chnl_state; /* Channel state */
256 struct t_l2c_ccb *p_next_ccb; /* Next CCB in the chain */
257 struct t_l2c_ccb *p_prev_ccb; /* Previous CCB in the chain */
258 struct t_l2c_linkcb *p_lcb; /* Link this CCB is assigned to */
260 UINT16 local_cid; /* Local CID */
261 UINT16 remote_cid; /* Remote CID */
263 TIMER_LIST_ENT timer_entry; /* CCB Timer List Entry */
265 tL2C_RCB *p_rcb; /* Registration CB for this Channel */
266 bool should_free_rcb; /* True if RCB was allocated on the heap */
268 #define IB_CFG_DONE 0x01
269 #define OB_CFG_DONE 0x02
270 #define RECONFIG_FLAG 0x04 /* True after initial configuration */
271 #define CFG_DONE_MASK (IB_CFG_DONE | OB_CFG_DONE)
273 UINT8 config_done; /* Configuration flag word */
274 UINT8 local_id; /* Transaction ID for local trans */
275 UINT8 remote_id; /* Transaction ID for local */
277 #define CCB_FLAG_NO_RETRY 0x01 /* no more retry */
278 #define CCB_FLAG_SENT_PENDING 0x02 /* already sent pending response */
281 tL2CAP_CFG_INFO our_cfg; /* Our saved configuration options */
282 tL2CAP_CH_CFG_BITS peer_cfg_bits; /* Store what peer wants to configure */
283 tL2CAP_CFG_INFO peer_cfg; /* Peer's saved configuration options */
285 fixed_queue_t *xmit_hold_q; /* Transmit data hold queue */
286 BOOLEAN cong_sent; /* Set when congested status sent */
287 UINT16 buff_quota; /* Buffer quota before sending congestion */
289 tL2CAP_CHNL_PRIORITY ccb_priority; /* Channel priority */
290 tL2CAP_CHNL_DATA_RATE tx_data_rate; /* Channel Tx data rate */
291 tL2CAP_CHNL_DATA_RATE rx_data_rate; /* Channel Rx data rate */
293 /* Fields used for eL2CAP */
294 tL2CAP_ERTM_INFO ertm_info;
296 UINT16 tx_mps; /* TX MPS adjusted based on current controller */
298 UINT8 fcr_cfg_tries; /* Max number of negotiation attempts */
299 BOOLEAN peer_cfg_already_rejected; /* If mode rejected once, set to TRUE */
300 BOOLEAN out_cfg_fcr_present; /* TRUE if cfg response shoulkd include fcr options */
302 #define L2CAP_CFG_FCS_OUR 0x01 /* Our desired config FCS option */
303 #define L2CAP_CFG_FCS_PEER 0x02 /* Peer's desired config FCS option */
304 #define L2CAP_BYPASS_FCS (L2CAP_CFG_FCS_OUR | L2CAP_CFG_FCS_PEER)
307 #if (L2CAP_NON_FLUSHABLE_PB_INCLUDED == TRUE)
308 BOOLEAN is_flushable; /* TRUE if channel is flushable */
311 #if (L2CAP_NUM_FIXED_CHNLS > 0) || (L2CAP_UCD_INCLUDED == TRUE)
312 UINT16 fixed_chnl_idle_tout; /* Idle timeout to use for the fixed channel */
317 /***********************************************************************
318 ** Define a queue of linked CCBs.
321 tL2C_CCB *p_first_ccb; /* The first channel in this queue */
322 tL2C_CCB *p_last_ccb; /* The last channel in this queue */
325 #if (L2CAP_ROUND_ROBIN_CHANNEL_SERVICE == TRUE)
327 /* Round-Robin service for the same priority channels */
328 #define L2CAP_NUM_CHNL_PRIORITY 3 /* Total number of priority group (high, medium, low)*/
329 #define L2CAP_CHNL_PRIORITY_WEIGHT 5 /* weight per priority for burst transmission quota */
330 #define L2CAP_GET_PRIORITY_QUOTA(pri) ((L2CAP_NUM_CHNL_PRIORITY - (pri)) * L2CAP_CHNL_PRIORITY_WEIGHT)
332 /* CCBs within the same LCB are served in round robin with priority */
333 /* It will make sure that low priority channel (for example, HF signaling on RFCOMM) */
334 /* can be sent to headset even if higher priority channel (for example, AV media channel) */
338 tL2C_CCB *p_serve_ccb; /* current serving ccb within priority group */
339 tL2C_CCB *p_first_ccb; /* first ccb of priority group */
340 UINT8 num_ccb; /* number of channels in priority group */
341 UINT8 quota; /* burst transmission quota */
344 #endif /* (L2CAP_ROUND_ROBIN_CHANNEL_SERVICE == TRUE) */
346 /* Define a link control block. There is one link control block between
347 ** this device and any other device (i.e. BD ADDR).
349 typedef struct t_l2c_linkcb {
350 BOOLEAN in_use; /* TRUE when in use, FALSE when not */
351 tL2C_LINK_STATE link_state;
353 TIMER_LIST_ENT timer_entry; /* Timer list entry for timeout evt */
354 UINT16 handle; /* The handle used with LM */
356 tL2C_CCB_Q ccb_queue; /* Queue of CCBs on this LCB */
358 tL2C_CCB *p_pending_ccb; /* ccb of waiting channel during link disconnect */
359 TIMER_LIST_ENT info_timer_entry; /* Timer entry for info resp timeout evt */
360 TIMER_LIST_ENT upda_con_timer; /* Timer entry for update connection parametr */
361 BD_ADDR remote_bd_addr; /* The BD address of the remote */
363 UINT8 link_role; /* Master or slave */
365 UINT8 cur_echo_id; /* Current id value for echo request */
366 tL2CA_ECHO_RSP_CB *p_echo_rsp_cb; /* Echo response callback */
367 UINT16 idle_timeout; /* Idle timeout */
368 BOOLEAN is_bonding; /* True - link active only for bonding */
370 UINT16 link_flush_tout; /* Flush timeout used */
372 UINT16 link_xmit_quota; /* Num outstanding pkts allowed */
373 UINT16 sent_not_acked; /* Num packets sent but not acked */
375 BOOLEAN partial_segment_being_sent; /* Set TRUE when a partial segment */
377 BOOLEAN w4_info_rsp; /* TRUE when info request is active */
378 UINT8 info_rx_bits; /* set 1 if received info type */
379 UINT32 peer_ext_fea; /* Peer's extended features mask */
380 list_t *link_xmit_data_q; /* Link transmit data buffer queue */
382 UINT8 peer_chnl_mask[L2CAP_FIXED_CHNL_ARRAY_SIZE];
383 #if (L2CAP_UCD_INCLUDED == TRUE)
384 UINT16 ucd_mtu; /* peer MTU on UCD */
385 fixed_queue_t *ucd_out_sec_pending_q; /* Security pending outgoing UCD packet */
386 fixed_queue_t *ucd_in_sec_pending_q; /* Security pending incoming UCD packet */
389 BT_HDR *p_hcit_rcv_acl; /* Current HCIT ACL buf being rcvd */
390 UINT16 idle_timeout_sv; /* Save current Idle timeout */
391 UINT8 acl_priority; /* L2C_PRIORITY_NORMAL or L2C_PRIORITY_HIGH */
392 tL2CA_NOCP_CB *p_nocp_cb; /* Num Cmpl pkts callback */
394 #if (L2CAP_NUM_FIXED_CHNLS > 0)
395 tL2C_CCB *p_fixed_ccbs[L2CAP_NUM_FIXED_CHNLS];
399 tBT_TRANSPORT transport;
400 #if (BLE_INCLUDED == TRUE)
401 tBLE_ADDR_TYPE ble_addr_type;
402 UINT16 tx_data_len; /* tx data length used in data length extension */
404 #define L2C_BLE_CONN_UPDATE_DISABLE 0x1 /* disable update connection parameters */
405 #define L2C_BLE_NEW_CONN_PARAM 0x2 /* new connection parameter to be set */
406 #define L2C_BLE_UPDATE_PENDING 0x4 /* waiting for connection update finished */
407 #define L2C_BLE_NOT_DEFAULT_PARAM 0x8 /* not using default connection parameters */
408 UINT8 conn_update_mask;
410 UINT16 min_interval; /* parameters as requested by peripheral */
418 #if (L2CAP_ROUND_ROBIN_CHANNEL_SERVICE == TRUE)
419 /* each priority group is limited burst transmission */
420 /* round robin service for the same priority channels */
421 tL2C_RR_SERV rr_serv[L2CAP_NUM_CHNL_PRIORITY];
422 UINT8 rr_pri; /* current serving priority group */
427 /* Define the L2CAP control structure
430 UINT8 l2cap_trace_level;
431 UINT16 controller_xmit_window; /* Total ACL window for all links */
433 UINT16 round_robin_quota; /* Round-robin link quota */
434 UINT16 round_robin_unacked; /* Round-robin unacked */
435 BOOLEAN check_round_robin; /* Do a round robin check */
437 BOOLEAN is_cong_cback_context;
439 tL2C_LCB lcb_pool[MAX_L2CAP_LINKS]; /* Link Control Block pool */
440 tL2C_CCB ccb_pool[MAX_L2CAP_CHANNELS]; /* Channel Control Block pool */
441 tL2C_RCB rcb_pool[MAX_L2CAP_CLIENTS]; /* Registration info pool */
443 tL2C_CCB *p_free_ccb_first; /* Pointer to first free CCB */
444 tL2C_CCB *p_free_ccb_last; /* Pointer to last free CCB */
446 UINT8 desire_role; /* desire to be master/slave when accepting a connection */
447 BOOLEAN disallow_switch; /* FALSE, to allow switch at create conn */
448 UINT16 num_lm_acl_bufs; /* # of ACL buffers on controller */
449 UINT16 idle_timeout; /* Idle timeout */
451 list_t *rcv_pending_q; /* Recv pending queue */
452 TIMER_LIST_ENT rcv_hold_tle; /* Timer list entry for rcv hold */
454 tL2C_LCB *p_cur_hcit_lcb; /* Current HCI Transport buffer */
455 UINT16 num_links_active; /* Number of links active */
457 #if (L2CAP_NON_FLUSHABLE_PB_INCLUDED == TRUE)
458 UINT16 non_flushable_pbf; /* L2CAP_PKT_START_NON_FLUSHABLE if controller supports */
459 /* Otherwise, L2CAP_PKT_START */
460 BOOLEAN is_flush_active; /* TRUE if an HCI_Enhanced_Flush has been sent */
463 #if L2CAP_CONFORMANCE_TESTING == TRUE
464 UINT32 test_info_resp; /* Conformance testing needs a dynamic response */
467 #if (L2CAP_NUM_FIXED_CHNLS > 0)
468 tL2CAP_FIXED_CHNL_REG fixed_reg[L2CAP_NUM_FIXED_CHNLS]; /* Reg info for fixed channels */
471 #if (BLE_INCLUDED == TRUE)
472 UINT16 num_ble_links_active; /* Number of LE links active */
473 BOOLEAN is_ble_connecting;
474 BD_ADDR ble_connecting_bda;
475 UINT16 controller_le_xmit_window; /* Total ACL window for all links */
476 tL2C_BLE_FIXED_CHNLS_MASK l2c_ble_fixed_chnls_mask; // LE fixed channels mask
477 UINT16 num_lm_ble_bufs; /* # of ACL buffers on controller */
478 UINT16 ble_round_robin_quota; /* Round-robin link quota */
479 UINT16 ble_round_robin_unacked; /* Round-robin unacked */
480 BOOLEAN ble_check_round_robin; /* Do a round robin check */
483 tL2CA_ECHO_DATA_CB *p_echo_data_cb; /* Echo data callback */
485 #if (defined(L2CAP_HIGH_PRI_CHAN_QUOTA_IS_CONFIGURABLE) && (L2CAP_HIGH_PRI_CHAN_QUOTA_IS_CONFIGURABLE == TRUE))
486 UINT16 high_pri_min_xmit_quota; /* Minimum number of ACL credit for high priority link */
487 #endif /* (L2CAP_HIGH_PRI_CHAN_QUOTA_IS_CONFIGURABLE == TRUE) */
494 /* Define a structure that contains the information about a connection.
495 ** This structure is used to pass between functions, and not all the
496 ** fields will always be filled in.
499 BD_ADDR bd_addr; /* Remote BD address */
500 UINT8 status; /* Connection status */
501 UINT16 psm; /* PSM of the connection */
502 UINT16 l2cap_result; /* L2CAP result */
503 UINT16 l2cap_status; /* L2CAP status */
504 UINT16 remote_cid; /* Remote CID */
508 typedef void (tL2C_FCR_MGMT_EVT_HDLR) (UINT8, tL2C_CCB *);
510 /* The offset in a buffer that L2CAP will use when building commands.
512 #define L2CAP_SEND_CMD_OFFSET 0
515 /* Number of ACL buffers to use for high priority channel
517 #if (!defined(L2CAP_HIGH_PRI_CHAN_QUOTA_IS_CONFIGURABLE) || (L2CAP_HIGH_PRI_CHAN_QUOTA_IS_CONFIGURABLE == FALSE))
518 #define L2CAP_HIGH_PRI_MIN_XMIT_QUOTA_A (L2CAP_HIGH_PRI_MIN_XMIT_QUOTA)
520 #define L2CAP_HIGH_PRI_MIN_XMIT_QUOTA_A (l2cb.high_pri_min_xmit_quota)
529 ************************************
531 #if (!defined L2C_DYNAMIC_MEMORY) || (L2C_DYNAMIC_MEMORY == FALSE)
534 extern tL2C_CB *l2c_cb_ptr;
535 #define l2cb (*l2c_cb_ptr)
539 /* Functions provided by l2c_main.c
540 ************************************
545 extern void l2c_process_timeout (TIMER_LIST_ENT *p_tle);
546 extern UINT8 l2c_data_write (UINT16 cid, BT_HDR *p_data, UINT16 flag);
547 extern void l2c_rcv_acl_data (BT_HDR *p_msg);
548 extern void l2c_process_held_packets (BOOLEAN timed_out);
550 /* Functions provided by l2c_utils.c
551 ************************************
553 extern tL2C_LCB *l2cu_allocate_lcb (BD_ADDR p_bd_addr, BOOLEAN is_bonding, tBT_TRANSPORT transport);
554 extern BOOLEAN l2cu_start_post_bond_timer (UINT16 handle);
555 extern void l2cu_release_lcb (tL2C_LCB *p_lcb);
556 extern tL2C_LCB *l2cu_find_lcb_by_bd_addr (BD_ADDR p_bd_addr, tBT_TRANSPORT transport);
557 extern tL2C_LCB *l2cu_find_lcb_by_handle (UINT16 handle);
558 extern void l2cu_update_lcb_4_bonding (BD_ADDR p_bd_addr, BOOLEAN is_bonding);
560 extern UINT8 l2cu_get_conn_role (tL2C_LCB *p_this_lcb);
561 extern BOOLEAN l2cu_set_acl_priority (BD_ADDR bd_addr, UINT8 priority, BOOLEAN reset_after_rs);
563 extern void l2cu_enqueue_ccb (tL2C_CCB *p_ccb);
564 extern void l2cu_dequeue_ccb (tL2C_CCB *p_ccb);
565 extern void l2cu_change_pri_ccb (tL2C_CCB *p_ccb, tL2CAP_CHNL_PRIORITY priority);
567 extern tL2C_CCB *l2cu_allocate_ccb (tL2C_LCB *p_lcb, UINT16 cid);
568 extern void l2cu_release_ccb (tL2C_CCB *p_ccb);
569 extern tL2C_CCB *l2cu_find_ccb_by_cid (tL2C_LCB *p_lcb, UINT16 local_cid);
570 extern tL2C_CCB *l2cu_find_ccb_by_remote_cid (tL2C_LCB *p_lcb, UINT16 remote_cid);
571 extern void l2cu_adj_id (tL2C_LCB *p_lcb, UINT8 adj_mask);
572 extern BOOLEAN l2c_is_cmd_rejected (UINT8 cmd_code, UINT8 id, tL2C_LCB *p_lcb);
574 extern void l2cu_send_peer_cmd_reject (tL2C_LCB *p_lcb, UINT16 reason,
575 UINT8 rem_id, UINT16 p1, UINT16 p2);
576 extern void l2cu_send_peer_connect_req (tL2C_CCB *p_ccb);
577 extern void l2cu_send_peer_connect_rsp (tL2C_CCB *p_ccb, UINT16 result, UINT16 status);
578 extern void l2cu_send_peer_config_req (tL2C_CCB *p_ccb, tL2CAP_CFG_INFO *p_cfg);
579 extern void l2cu_send_peer_config_rsp (tL2C_CCB *p_ccb, tL2CAP_CFG_INFO *p_cfg);
580 extern void l2cu_send_peer_config_rej (tL2C_CCB *p_ccb, UINT8 *p_data, UINT16 data_len, UINT16 rej_len);
581 extern void l2cu_send_peer_disc_req (tL2C_CCB *p_ccb);
582 extern void l2cu_send_peer_disc_rsp (tL2C_LCB *p_lcb, UINT8 remote_id, UINT16 local_cid, UINT16 remote_cid);
583 extern void l2cu_send_peer_echo_req (tL2C_LCB *p_lcb, UINT8 *p_data, UINT16 data_len);
584 extern void l2cu_send_peer_echo_rsp (tL2C_LCB *p_lcb, UINT8 id, UINT8 *p_data, UINT16 data_len);
585 extern void l2cu_send_peer_info_rsp (tL2C_LCB *p_lcb, UINT8 id, UINT16 info_type);
586 extern void l2cu_reject_connection (tL2C_LCB *p_lcb, UINT16 remote_cid, UINT8 rem_id, UINT16 result);
587 extern void l2cu_send_peer_info_req (tL2C_LCB *p_lcb, UINT16 info_type);
588 extern void l2cu_set_acl_hci_header (BT_HDR *p_buf, tL2C_CCB *p_ccb);
589 extern void l2cu_check_channel_congestion (tL2C_CCB *p_ccb);
590 extern void l2cu_disconnect_chnl (tL2C_CCB *p_ccb);
592 #if (L2CAP_NON_FLUSHABLE_PB_INCLUDED == TRUE)
593 extern void l2cu_set_non_flushable_pbf(BOOLEAN);
596 #if (BLE_INCLUDED == TRUE)
597 extern void l2cu_send_peer_ble_par_req (tL2C_LCB *p_lcb, UINT16 min_int, UINT16 max_int, UINT16 latency, UINT16 timeout);
598 extern void l2cu_send_peer_ble_par_rsp (tL2C_LCB *p_lcb, UINT16 reason, UINT8 rem_id);
601 extern BOOLEAN l2cu_initialize_fixed_ccb (tL2C_LCB *p_lcb, UINT16 fixed_cid, tL2CAP_FCR_OPTS *p_fcr);
602 extern void l2cu_no_dynamic_ccbs (tL2C_LCB *p_lcb);
603 extern void l2cu_process_fixed_chnl_resp (tL2C_LCB *p_lcb);
605 /* Functions provided by l2c_ucd.c
606 ************************************
608 #if (L2CAP_UCD_INCLUDED == TRUE)
609 void l2c_ucd_delete_sec_pending_q(tL2C_LCB *p_lcb);
610 void l2c_ucd_enqueue_pending_out_sec_q(tL2C_CCB *p_ccb, void *p_data);
611 BOOLEAN l2c_ucd_check_pending_info_req(tL2C_CCB *p_ccb);
612 BOOLEAN l2c_ucd_check_pending_out_sec_q(tL2C_CCB *p_ccb);
613 void l2c_ucd_send_pending_out_sec_q(tL2C_CCB *p_ccb);
614 void l2c_ucd_discard_pending_out_sec_q(tL2C_CCB *p_ccb);
615 BOOLEAN l2c_ucd_check_pending_in_sec_q(tL2C_CCB *p_ccb);
616 void l2c_ucd_send_pending_in_sec_q(tL2C_CCB *p_ccb);
617 void l2c_ucd_discard_pending_in_sec_q(tL2C_CCB *p_ccb);
618 BOOLEAN l2c_ucd_check_rx_pkts(tL2C_LCB *p_lcb, BT_HDR *p_msg);
619 BOOLEAN l2c_ucd_process_event(tL2C_CCB *p_ccb, UINT16 event, void *p_data);
622 #if (BLE_INCLUDED == TRUE)
623 extern void l2cu_send_peer_ble_par_req (tL2C_LCB *p_lcb, UINT16 min_int, UINT16 max_int, UINT16 latency, UINT16 timeout);
624 extern void l2cu_send_peer_ble_par_rsp (tL2C_LCB *p_lcb, UINT16 reason, UINT8 rem_id);
627 extern BOOLEAN l2cu_initialize_fixed_ccb (tL2C_LCB *p_lcb, UINT16 fixed_cid, tL2CAP_FCR_OPTS *p_fcr);
628 extern void l2cu_no_dynamic_ccbs (tL2C_LCB *p_lcb);
629 extern void l2cu_process_fixed_chnl_resp (tL2C_LCB *p_lcb);
632 /* Functions provided for Broadcom Aware
633 ****************************************
635 extern BOOLEAN l2cu_check_feature_req (tL2C_LCB *p_lcb, UINT8 id, UINT8 *p_data, UINT16 data_len);
636 extern void l2cu_check_feature_rsp (tL2C_LCB *p_lcb, UINT8 id, UINT8 *p_data, UINT16 data_len);
637 extern void l2cu_send_feature_req (tL2C_CCB *p_ccb);
639 extern tL2C_RCB *l2cu_allocate_rcb (UINT16 psm);
640 extern tL2C_RCB *l2cu_find_rcb_by_psm (UINT16 psm);
641 extern void l2cu_release_rcb (tL2C_RCB *p_rcb);
643 extern UINT8 l2cu_process_peer_cfg_req (tL2C_CCB *p_ccb, tL2CAP_CFG_INFO *p_cfg);
644 extern void l2cu_process_peer_cfg_rsp (tL2C_CCB *p_ccb, tL2CAP_CFG_INFO *p_cfg);
645 extern void l2cu_process_our_cfg_req (tL2C_CCB *p_ccb, tL2CAP_CFG_INFO *p_cfg);
646 extern void l2cu_process_our_cfg_rsp (tL2C_CCB *p_ccb, tL2CAP_CFG_INFO *p_cfg);
648 extern void l2cu_device_reset (void);
649 extern tL2C_LCB *l2cu_find_lcb_by_state (tL2C_LINK_STATE state);
650 extern BOOLEAN l2cu_lcb_disconnecting (void);
652 extern BOOLEAN l2cu_create_conn (tL2C_LCB *p_lcb, tBT_TRANSPORT transport);
653 extern BOOLEAN l2cu_create_conn_after_switch (tL2C_LCB *p_lcb);
654 extern BT_HDR *l2cu_get_next_buffer_to_send (tL2C_LCB *p_lcb);
655 extern void l2cu_resubmit_pending_sec_req (BD_ADDR p_bda);
656 extern void l2cu_initialize_amp_ccb (tL2C_LCB *p_lcb);
657 extern void l2cu_adjust_out_mps (tL2C_CCB *p_ccb);
659 /* Functions provided by l2c_link.c
660 ************************************
662 extern BOOLEAN l2c_link_hci_conn_req (BD_ADDR bd_addr);
663 extern BOOLEAN l2c_link_hci_conn_comp (UINT8 status, UINT16 handle, BD_ADDR p_bda);
664 extern BOOLEAN l2c_link_hci_disc_comp (UINT16 handle, UINT8 reason);
665 extern BOOLEAN l2c_link_hci_qos_violation (UINT16 handle);
666 extern void l2c_link_timeout (tL2C_LCB *p_lcb);
667 extern void l2c_info_timeout (tL2C_LCB *p_lcb);
668 extern void l2c_link_check_send_pkts (tL2C_LCB *p_lcb, tL2C_CCB *p_ccb, BT_HDR *p_buf);
669 extern void l2c_link_adjust_allocation (void);
670 extern void l2c_link_process_num_completed_pkts (UINT8 *p);
671 extern void l2c_link_process_num_completed_blocks (UINT8 controller_id, UINT8 *p, UINT16 evt_len);
672 extern void l2c_link_processs_num_bufs (UINT16 num_lm_acl_bufs);
673 extern UINT8 l2c_link_pkts_rcvd (UINT16 *num_pkts, UINT16 *handles);
674 extern void l2c_link_role_changed (BD_ADDR bd_addr, UINT8 new_role, UINT8 hci_status);
675 extern void l2c_link_sec_comp (BD_ADDR p_bda, tBT_TRANSPORT trasnport, void *p_ref_data, UINT8 status);
676 extern void l2c_link_segments_xmitted (BT_HDR *p_msg);
677 extern void l2c_pin_code_request (BD_ADDR bd_addr);
678 extern void l2c_link_adjust_chnl_allocation (void);
680 #if (BLE_INCLUDED == TRUE)
681 extern void l2c_link_processs_ble_num_bufs (UINT16 num_lm_acl_bufs);
684 #if L2CAP_WAKE_PARKED_LINK == TRUE
685 extern BOOLEAN l2c_link_check_power_mode ( tL2C_LCB *p_lcb );
686 #define L2C_LINK_CHECK_POWER_MODE(x) l2c_link_check_power_mode ((x))
687 #else // L2CAP_WAKE_PARKED_LINK
688 #define L2C_LINK_CHECK_POWER_MODE(x) (FALSE)
689 #endif // L2CAP_WAKE_PARKED_LINK
691 #if L2CAP_CONFORMANCE_TESTING == TRUE
692 /* Used only for conformance testing */
693 extern void l2cu_set_info_rsp_mask (UINT32 mask);
696 /* Functions provided by l2c_csm.c
697 ************************************
699 extern void l2c_csm_execute (tL2C_CCB *p_ccb, UINT16 event, void *p_data);
701 extern void l2c_enqueue_peer_data (tL2C_CCB *p_ccb, BT_HDR *p_buf);
704 /* Functions provided by l2c_fcr.c
705 ************************************
707 extern void l2c_fcr_cleanup (tL2C_CCB *p_ccb);
708 extern void l2c_fcr_proc_pdu (tL2C_CCB *p_ccb, BT_HDR *p_buf);
709 extern void l2c_fcr_proc_tout (tL2C_CCB *p_ccb);
710 extern void l2c_fcr_proc_ack_tout (tL2C_CCB *p_ccb);
711 extern void l2c_fcr_send_S_frame (tL2C_CCB *p_ccb, UINT16 function_code, UINT16 pf_bit);
712 extern BT_HDR *l2c_fcr_clone_buf (BT_HDR *p_buf, UINT16 new_offset, UINT16 no_of_bytes);
713 extern BOOLEAN l2c_fcr_is_flow_controlled (tL2C_CCB *p_ccb);
714 extern BT_HDR *l2c_fcr_get_next_xmit_sdu_seg (tL2C_CCB *p_ccb, UINT16 max_packet_length);
715 extern void l2c_fcr_start_timer (tL2C_CCB *p_ccb);
717 /* Configuration negotiation */
718 extern UINT8 l2c_fcr_chk_chan_modes (tL2C_CCB *p_ccb);
719 extern BOOLEAN l2c_fcr_adj_our_req_options (tL2C_CCB *p_ccb, tL2CAP_CFG_INFO *p_cfg);
720 extern void l2c_fcr_adj_our_rsp_options (tL2C_CCB *p_ccb, tL2CAP_CFG_INFO *p_peer_cfg);
721 extern BOOLEAN l2c_fcr_renegotiate_chan(tL2C_CCB *p_ccb, tL2CAP_CFG_INFO *p_cfg);
722 extern UINT8 l2c_fcr_process_peer_cfg_req(tL2C_CCB *p_ccb, tL2CAP_CFG_INFO *p_cfg);
723 extern void l2c_fcr_adj_monitor_retran_timeout (tL2C_CCB *p_ccb);
724 extern void l2c_fcr_stop_timer (tL2C_CCB *p_ccb);
726 /* Functions provided by l2c_ble.c
727 ************************************
729 #if (BLE_INCLUDED == TRUE)
730 extern BOOLEAN l2cble_create_conn (tL2C_LCB *p_lcb);
731 extern void l2cble_process_sig_cmd (tL2C_LCB *p_lcb, UINT8 *p, UINT16 pkt_len);
732 extern void l2cble_conn_comp (UINT16 handle, UINT8 role, BD_ADDR bda, tBLE_ADDR_TYPE type,
733 UINT16 conn_interval, UINT16 conn_latency, UINT16 conn_timeout);
734 extern BOOLEAN l2cble_init_direct_conn (tL2C_LCB *p_lcb);
735 extern void l2cble_notify_le_connection (BD_ADDR bda);
736 extern void l2c_ble_link_adjust_allocation (void);
737 extern void l2cble_process_conn_update_evt (UINT16 handle, UINT8 status, UINT16 conn_interval,
738 UINT16 conn_latency, UINT16 conn_timeout);
740 #if (defined BLE_LLT_INCLUDED) && (BLE_LLT_INCLUDED == TRUE)
741 extern void l2cble_process_rc_param_request_evt(UINT16 handle, UINT16 int_min, UINT16 int_max,
742 UINT16 latency, UINT16 timeout);
745 extern void l2cble_update_data_length(tL2C_LCB *p_lcb);
746 extern void l2cble_set_fixed_channel_tx_data_length(BD_ADDR remote_bda, UINT16 fix_cid,
748 extern void l2c_send_update_conn_params_cb(tL2C_LCB *p_lcb, UINT8 status);
749 extern void l2cble_process_data_length_change_event(UINT16 handle, UINT16 tx_data_len,
753 extern void l2cu_process_fixed_disc_cback (tL2C_LCB *p_lcb);